- 您現在的位置：買賣IC網 > PDF目錄1954 > MLX90308LDF-DAA-000-TU (Melexis Technologies NV)IC SENSOR PROG INTERFACE 16-SOIC PDF資料下載
參數資料
| 型號： | MLX90308LDF-DAA-000-TU |
| 廠商： | Melexis Technologies NV |
| 文件頁數： | 3/28頁 |
| 文件大小： | 0K |
| 描述： | IC SENSOR PROG INTERFACE 16-SOIC |
| 標準包裝： | 46 |
| 類型： | 傳感器接口 |
| 輸入類型： | 電壓 |
| 輸出類型： | 電壓 |
| 接口： | UART |
| 電流 - 電源： | 5mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 管件 |
| 產品目錄頁面： | 1460 (CN2011-ZH PDF) |
| 配用： | EVB90308-ND - DEMO KIT MLX90308 SENS INTERFACE |
| 其它名稱： | MLX90308CCC MLX90308D-LDF MLX90308LDF MLX90308LDF-DA MLX90308LDF-DA-ND MLX90308LDF-ND |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
MLX90308
Programmable Sensor Interface
3901090308
Rev 007
Page 11
May/12
Different Modes
Analog Mode
The parameters OF and GN represent, respectively,
offset correction and span control, while OFTCi and
GNTCi
represent
their
temperature
coefficients
(thermal zero shift and thermal span shift). After reset,
the firmware continuously calculates the offset and
gain DAC settings as follows: The EEPROM holds
parameters GN, OF, OFTCi and GNTCi, where “i” is
the gap number and can be 1 < i < 4. The transfer
OFFSET
DAC_OFFSET (new value) ~ OF[9:0]+[OFTCi* dT]
OF[9:0] = Fixed Gain, bytes 4 and 17 in EEPROM.
OFTCi = Offset for a given temperature
segment I. OFTCiL and OFTCiH in
EEPROM table.
dT = Temp. change within the appropriate gap.
Calculation of the offset for a given temperature seg-
ment is performed the same way as for the gain.
function is described below.
Vout
=
FG
*
DAC_GAIN
*
CSGN[2:0]
*
{Vin+DAC_OFFSET+CSOF}
Iout = FG * DAC_GAIN * CSGN[1:0] *
{Vin+DAC_OFFSET+CSOF} * 8.85mA/V
FG = Hardware Gain (~20V/V). Part of the hardware
design, and not changeable.
CSGN = Course Gain, part of byte 2 in EEPROM.
CSOF = Coarse Offset, part of byte 2 in EEPROM.
GAIN
DAC_GAIN (new value) ~ GN[9:0] + [GNTCi * dT]
GN[9:0] = Fixed Gain, bytes 3 and 17 in EEPROM.
GNTCi = Gain TC for a given temperature
segment I. GNTCiL and GNTCiH in
EEPROM table.
dT = Temp. change within the appropriate gap.
How to calculate gain in the first temp. gap?:
DAC_GAIN = GN[9:0] - GNTC1 * (T1 – Temp_f1)
How to calculate gain in the other temp. gaps?:
2nd gap: DAC_GAIN = GN[9:0] + GNTC2 *
(Temp_f2 – T1)
3th gap: DAC_GAIN = DAC_GAIN2 + GNTC3 *
(Temp_f3 – T2)
4th gap: DAC_GAIN = DAC_GAIN3 + GNTC4 *
(Temp_f4 – T3)
Where:
Temp_f = Filtered temp. (previously described).
If GNTC1 > 2047 => DAC_GAIN
If GNTC2,3,4 > 2047 => DAC_GAIN
[V/V]
Digital Mode
The MLX90308 firmware provides the capability of
digitally processing the sensor signal in addition to the
analog processing. This capability allows for signal
correction.
Signal Correction
While in digital mode the firmware can perform signal
correction. This is an adjustment to the output level
based
on
the
input
signal
level.
Adjustment
coefficients can be set for five different signal ranges.
The output is obtained by the following formula:
1st gap: Output = (Signal ) * PC1 + Poff
Where:
Signal = input signal measurement;
Poff = Pressure ordinate = P1
PC1 = programmed coefficient first gap.
Following gaps:
Gap i: Output = (Signal – Pi) * PCi + Poff_i
Where
Signal = input signal measurement;
Poff_i = Pressure ordinate (i = 2,3,4,5)
Pi = Pressure signal point (i = 2,3,4,5)
PCi = programmed coefficient first gap (i = 2,3,4,5).
The PCi coefficients are coded on 12 bits: one bit for
the sign, one for the unity, and the rest for the
decimals. The Pi are coded on 10 bits (0-3FFh) in
high-low order.
PNB_TNB: contains the number of signal points,
coded on the four MSB’s. The four LSB’s are reserved
for the number of temperature points. See Table 4 and
Table 5.
相關PDF資料 |
PDF描述 |
|---|---|
| MLX90314LDF-BAA-000-TU | IC SENSOR PROG HIGH GAIN 16-SOIC |
| MM908E621ACDWBR2 | IC SW QUAD HB/TRPL HISID 54-SOIC |
| MM908E622ACEK | IC HALF-BRIDGE QUAD 54-SOIC |
| MM908E624ACEWR2 | IC SWITCH TRPL HI MCU/LIN 54SOIC |
| MM908E625ACDWB | IC QUAD HALF BRDG MCU/LIN 54SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MLX90308LUF | 制造商:MELEXIS 制造商全稱:Melexis Microelectronic Systems 功能描述:Programmable Sensor Interface |
| MLX90313 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable IR Sensor Interface |
| MLX90313KDF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable IR Sensor Interface |
| MLX90314 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Sensor Interface |
| MLX90314AB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Sensor Interface |
發布緊急采購，3分鐘左右您將得到回復。