- 您現在的位置：買賣IC網 > PDF目錄383606 > MIC2580A-1.0BTS (MICREL INC) Hot-Swap PCI Power Controller PDF資料下載
參數資料
| 型號： | MIC2580A-1.0BTS |
| 廠商： | MICREL INC |
| 元件分類： | 電源管理 |
| 英文描述： | Hot-Swap PCI Power Controller |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| 封裝： | TSSOP-24 |
| 文件頁數： | 18/21頁 |
| 文件大?。?/td> | 252K |
| 代理商： | MIC2580A-1.0BTS |
MIC2580A
Functional Description
Start-Up Sequence
The start-up sequence iniates after all four supplies are
connected to the inputs and then /ON is asserted by
transistioning from high to low. During the start-up sequence,
all four gates ramp up at a rate determined by C
. During
this time /PWRGD is deasserted until all four supplies are
within specified levels. When /PWRGD is asserted the power-
on-reset signal /POR timer begins. The time period is defined
by C
. Refer to Figure 1 for a timing diagram of the signals
during the start-up sequence.
During the start-up sequence, a current source charges
C
at a constant rate until a threshold voltage of 2.4V is
reached. This period of time defines an interval during which
overcurrent events are ignored. This prevents high inrush
currents that normally occur when charging capacitance
erroneously asserting /FAULT. The magnitude of the start-
up time, t
START
is defined by C
START
.
The MIC2580A employs foldback current limiting that en-
sures the device starts up in current limit. This minimizes high
inrush currents due to ramping a voltage into capacitance
regardless of the size of the load capacitance.
Overcurrent Detection
The MIC2580A senses overcurrent via the use of external
sense resistors for the 5V and 3.3V supply rails. When the
sense voltage across these resistors is greater than or equal
to 50mV an overcurrent condition is detected. Therefore the
overcurrent set point is determined by I
= 50mV/R
.
For the +12V and –12V supply rails overcurrent detection is
set internally at 1.3A and –0.5A respectively.
When an overcurrent condition is detected /FAULT is as-
serted only if the overcurrent condition lasts for a minimum
time period of 10
s. This delay prevents spurious noise from
the system erroneously tripping the circuit breaker and as-
serting /FAULT. Upon /FAULT being asserted an internal
latch is set that immediately turns off all four supplies to
prevent further damage to the system. Toggling /ON will reset
the latch and initiate another start-up sequence. Figures 2
and 3 depict the timing for two fault conditions.
Micrel, Inc.
MIC2580A
18
February 2005
Thermal Shutdown
The +12V and –12V internal MOSFET switches are protected
by current limit and overtemperature shutdown circuitry.
When the die temperature exceeds 160
C, /FAULT is as-
serted and all supplies are shut off. The power dissipated in
the MIC2580A is primarily due to the sum of current flowing
through the internal MOSFET switches and, to a lesser
extent, power dissipated due to the supply current. To com-
pute the total power dissipation of the MIC2580A the follow-
ing equation is used:
P
D(total)
= P
D(+12V switch)
+ P
D(–12V switch)
+ P
D(supplies)
where:
P
D(switches)
= R
DS(on)
×
I
OUT2
P
D(supplies)
= V
SUPPLY
I
SUPPLY
To relate this to operating junction temperature:
T
J
= P
D
×
θ
JA
+ T
A
where:
T
A
= ambient temperature
JA
= package thermal resistance
Precharge Voltage
For CompactPCI applications, the MIC2580A-1.0BSM/BTS
integrates a 1V
20% voltage source that satisfies
CompactPCI precharge requirements. The voltage source
can provide up to 10mA. For higher current, the MIC2580A-
1.6BSM/BTS integrates a 1.6V
±
20% voltage source to bias
a NPN transistor.
MIC2580A-1.6
VPCHG
DATA
BUS
R
I > 10mA
+5V
Figure 5. Voltage Source
Turnoff
Deasserting /ON will turn off all four supplies. Alternatively
driving /FAULT low will turn off all supplies but will not latch
the supplies off. Releasing /FAULT will initiate a new start
sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2580A-1.6BTS | Hot-Swap PCI Power Controller |
| MIC2580 | Hot-Swap PCI Power Controller(熱交換PCI功率控制器) |
| MIC2588 | Single-Channel, Negative High-Voltage Hot Swap Power Controllers |
| MIC2588-1BM | Single-Channel, Negative High-Voltage Hot Swap Power Controllers |
| MIC2588-2BM | Single-Channel, Negative High-Voltage Hot Swap Power Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2582JBM | 制造商:Micrel Inc 功能描述: |
| MIC2582-JBM | 功能描述:IC CTRLR HOTSWAP 1CHAN POS 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2582-JBM TR | 功能描述:IC CTRLR HOTSWAP 1CHAN POS 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2582-JYM | 功能描述:熱插拔功率分布 Single-Channel Hot-Swap Controller - 100mV Fast-Trip Threshold - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2582-JYM TR | 功能描述:熱插拔功率分布 Single-Channel Hot-Swap Controller - 100mV Fast-Trip Threshold - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。