參數資料
型號： MIC2569YQS TR
廠商： Micrel Inc
文件頁數： 11/15頁
文件大?。?/td> 715K
描述： IC POWER SWITCH CABLECARD 16QSOP
標準包裝： 2,500
類型： 熱交換控制器
應用： 衛星/線纜/DVR/電視機頂盒，視頻記錄器，游戲控制臺
內部開關： 是
電流限制： 2.3A
電源電壓： 3.3V，5V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 16-QSOP
包裝： 帶卷 (TR)
Micrel, Inc.
MIC2569
 
 
September 2007 
11
M9999-092507-C
 (408) 944-0800
 
Functional Description
3.3VIN and 5.0VIN
3.3VIN and 5VIN are the input power supplies for
the MIC2569. 3.3VIN powers the MIC2569s
internal functions; as well as, VCC, and VPP1 and
VPP2. 5VIN provides power to VPP1 and VPP2.
Tables 1 and 2 shows the control states which
supply is provided to which output
C0, C1, C2 (States Controls)
C0, C1, and C2 control the output conditions for
VCC, VPP1 and VPP2. C0, C1, and C2 are inputs
to the MIC2569 provided by the host. See Tables 1
and 2 for a complete listing. Also see the
Application Information section.
VCC
VCC   provides   the   main   3.3V   supply   to   the
CableCARD device. VCC is protected against high
current conditions and short circuits. The minimum
current limit is set to 1.3A from 3.3VIN. Break-
before-make
switching
prevents
crossed
connections during state changes. The VCC output
depends on the host / card combination. See
Tables 1 and 2 for a complete listing. Also see the
Application Information section.
VPP1, VPP2 (VPP1/2)
VPP1 and VPP2 provide the 3.3V and 5.0V supplies
to the CableCARD device. VPP1 and VPP2 are
protected against high current conditions and short
circuits. The minimum current limit is set to a
minimum of 150mA. Note: VPP1 and VPP2 are
powered separately with each having a current limit
of 150mA Break-before-make switching prevents
crossed connections during state changes. The
VPP1/2   output   depends   on   the   host   /   card
combination. See Tables 1 and 2 for a complete
listing. Also see the Application Information section.
Soft-Start
The VCC, VPP1 and VPP2 outputs are all slew rate
controlled insuring a soft-start turn-on characteristic.
Soft-starting is in effect anytime a supply ramps from a
0V condition or switches between voltages, as in the
case of the VPP outputs.
Thermal Shutdown
Because electrical faults can cause significant heating in
power   switches,   MIC2569   monitors   its   internal
temperature   and   will   shut   down   should   the   die
temperature reach 140癈. When the die temperature
has dropped by about 10 degrees, MIC2569 will
reactivate its outputs. If there is still a problem, the
effected power switch will again get hot, shutting off all
outputs. This power cycling action will continue as long
as the fault persists. Once removed, MIC2569 will
resume normal operation.
FAULT/
FAULT/ is a LOW true open drain output which signals
an over current or over-temp condition. As an open drain
device, this output can be wire ORd with other FAULT/
outputs to a single input pin on the host. For proper
operation this output must be pulled-up to the logic
supply rail by an external resistor. This resistor can be
large in value, but not so large that leakage currents
caused by surface contamination can cause a false
indication of a fault condition. For this reason it is
recommended that the pull-up resistor be 300k& or less.
FAULT/ is delayed with respect to an over current
condition being detected. This is to prevent brief current
spikes from triggering an interrupt to the system host.
The delay is on the order of 12ms. Any fault lasting over
8 ms triggers the FAULT/ output. There is no delay for
thermal faults. Any over-temp condition is reported
immediately.
UVLO (Under Voltage Lockout)
An under-voltage lock out (UVLO) circuit monitors the
3.3VIN rail and keeps MIC2569 disabled until the input
voltage reaches the minimum level needed for proper
operation. Below this voltage the output switches are
OFF and all functionality is disabled.
相關PDF資料
PDF描述
MIC2583R-MBQS TR IC CTRLR HOT SWAP 200MV 16-QSOP
MIC2585-2MBTS TR IC CTRLR HOT SWAP DUAL 24-TSSOP
MIC2586R-2BM TR IC CTRLR/SEQ HOT SWAP 14-SOIC
MIC2587R-2BM TR IC CTRLR HOT SWAP POS HV 8-SOIC
MIC2590B-5BTQ TR IC PCI HOT PLUG CTLR DUAL 48TQFP
相關代理商/技術參數
參數描述
MIC2570-1BM 功能描述:IC REG BOOST 2.85V/3.3V/5V 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12
MIC2570-1BM TR 功能描述:IC REG BOOST 2.85V/3.3V/5V 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12
MIC2570-1YM 功能描述:直流/直流開關調節器 Two Cell Boost Regulator (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MIC2570-1YM TR 功能描述:直流/直流開關調節器 Two Cell Boost Regulator (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MIC2570-2BM 功能描述:IC REG BOOST ADJ 1A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*