- 您現在的位置：買賣IC網 > PDF目錄383605 > MIC2537-2BM (MICREL INC) Quad Power Distribution Switch Preliminary Information PDF資料下載
參數資料
| 型號： | MIC2537-2BM |
| 廠商： | MICREL INC |
| 元件分類： | 電源管理 |
| 英文描述： | Quad Power Distribution Switch Preliminary Information |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封裝： | SOP-16 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 88K |
| 代理商： | MIC2537-2BM |
MIC2537
Functional Description
The MIC2537-1 and MIC2537-2 are quad high-side switches
with active-high and active-low enable inputs, respectively.
Fault conditions turn off or inhibit turn-on of one or more of the
output transistors, depending upon the type of fault, and
activate the open-drain error flag transistors making them
sink current to ground.
Input and Output
IN (input) is the power supply connection to the logic circuitry
and the drain of each output MOSFET. OUTx (output) is the
source of each respective MOSFET. In a typical circuit,
current flows through the switch from IN to OUTx toward the
load. If V
OUT
is greater than V
IN
, current will flow from OUT
to IN since the MOSFET is bidirectional when on.
The output MOSFET and driver circuitry are also designed to
allow the MOSFET source to be externally forced to a higher
voltage than the drain (V
OUTx
> V
IN
) when the output is off. In
this situation, the MIC2537 prevents reverse current flow.
Thermal Shutdown
Thermal shutdown shuts off the affected output MOSFET
and signals the corresponding fault flags if the die tempera-
ture exceeds 135
°
C. 10
°
C of hysteresis prevents the switch
from turning on until the die temperature drops to 125
°
C.
Overtemperature detection functions only when at least one
switch is enabled.
Current-Limit Induced Thermal Shutdown
Internal circuitry increases the output MOSFET on-resis-
tance until the series combination of the MOSFET on-resis-
tance and the load impedance limits output current to ap-
proximately 200mA. The resulting increase in power dissipa-
tion may cause the shorted channel to go into thermal
shutdown. In addition, even though individual channels are
thermally isolated, it is possible they may shut down when an
adjacent channel is shorted. When this is undesirable, shut-
down of the channels not shorted can be avoided by exter-
nally responding to the fault and disabling the current limited
channel before the shutdown temperature is reached. The
delay between the flag indication of a current limit fault and
thermal shutdown will vary with ambient temperature, board
layout, and load impedance, but is typically several seconds.
The USB controller must therefore recognize a fault and
disable the appropriate channel within this time.
Micrel
December 1999
8
MIC2537
Current Sensing and Limiting
The current-limit threshold is preset internally. The preset
level prevents damage to the output MOSFET and external
load but allows a minimum current of 0.15A through the
output MOSFET of each channel.
The current-limit circuit senses a portion of the output FET
switch current. The current sense resistor shown in the block
diagram is virtual and has no voltage drop. The reaction to an
overcurrent condition varies with the following three sce-
narios:
Switch Enabled into Short Circuit
If a switch is powered on or enabled into an excessive load or
short circuit, the switch immediately goes into a constant-
current mode, slowly increasing the output voltage. The fault
flag goes low until the load is reduced.
Short Circuit Applied to Output
When a heavy load or short circuit is applied to an enabled
switch, a large transient current may flow until the current-
limit circuitry responds. Once this occurs, the device limits
current to less than the short circuit current-limit specification.
See the
“
Functional Characteristics: Current-Limit Transient
Response graph for details.
Current-Limit Response
The MIC2537 current-limit profile exhibits a small foldback
effect of approximately 100mA. Once this current-limit thresh-
old is exceeded the device enters constant-current mode.
This constant current is specified as the short-circuit current
limit in the
“
Electrical Characteristics
”
table. It is important to
note that the MIC2537 will deliver load current up to the
current-limit threshold. See the
“
Functional Characteristics:
Current-Limit Response
”
graph for details.
Fault Flag
FLGx is an open-drain N-channel MOSFET output. Fault
flags are active (low) for current limit or thermal shutdown.
Each flag output MOSFET is capable of sinking a 10mA load
to approximately 200mV above ground. Several FLGx pins
may be wired-NOR connected to a common pull-up resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2548-2BMM | Replaced by PT6522 : |
| MIC2544-1 | Programmable Current Limit High-Side Switch Preliminary Information |
| MIC2544-1BM | Programmable Current Limit High-Side Switch Preliminary Information |
| MIC2544-1BMM | Programmable Current Limit High-Side Switch Preliminary Information |
| MIC2544-2BM | Programmable Current Limit High-Side Switch Preliminary Information |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2537-2BM TR | 功能描述:IC USB SWITCH QUAD 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源分配開關 系列:- 特色產品:XRP252 Switches 標準包裝:1 系列:- 類型:高端開關 輸出數:2 Rds（開）:140 毫歐 內部開關:是 電流限制:1.15A 輸入電壓:1.75 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN（3x3） 包裝:Digi-Reel® 其它名稱:1016-1691-6 |
| MIC2537-2YM | 功能描述:電源開關 IC - USB Quad USB Switch (Lead Free) RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MIC2537-2YM TR | 功能描述:電源開關 IC - USB Quad USB Switch (Lead Free) RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MIC25383R-JBQS | 制造商:RF Micro Devices Inc 功能描述: |
| MIC25400YML TR | 功能描述:直流/直流開關調節器 2A Dual Output PWM Synchronous Buck Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。