- 您現在的位置：買賣IC網 > PDF目錄383605 > MIC2506 (Micrel Semiconductor,Inc.) Dual 1A High-Side Switches(雙集成 1A高邊電源開關) PDF資料下載
參數資料
| 型號： | MIC2506 |
| 廠商： | Micrel Semiconductor,Inc. |
| 英文描述： | Dual 1A High-Side Switches(雙集成 1A高邊電源開關) |
| 中文描述： | 第1A雙高邊開關（雙集成1A條高邊電源開關） |
| 文件頁數： | 9/12頁 |
| 文件大小： | 147K |
| 代理商： | MIC2506 |
April 1998
9
MIC2505/2506
MIC2505/2506
Applications Information
Supply Filtering
A 0.1
μ
F to 1
μ
F bypass capacitor from IN to GND, located at
the device is strongly recommended to control supply tran-
sients. Without a bypass capacitor, an output short may
cause sufficient ringing on the input (from supply lead induc-
tance) to destroy the internal control circuitry.
Input transients must not exceed the absolute maximum
supply voltage (V
IN max
= 7.5V) even for a short duration.
Micrel
ON
OFF
MIC2505BM
CTL
OUT
FLG
GND
OUT
GATE
IN
IN
1
8
2
7
3
6
4
5
0.1μF to 1μF
2.7V to 7.5V
Figure 1. Supply Bypassing
The bypass capacitor may be omitted only if board design
precautions are followed, such as using extremely short
supply leads or power and ground planes.
Control Input
CTL must be driven logic high or logic low, or be pulled high
or low for a clearly defined input. Floating the input may cause
unpredictable operation. Add a diode clamp if negative spikes
may occur. See Figure 2.
Open-Load Detection
Refer to “Typical Applications” (first page). Open-load detec-
tion is available only on the MIC2505 and MIC2506. For USB
power distribution applications, the open-load detection fea-
ture is not included in the MIC2505-1 or -2 versions.
The optional open-load detection resistor supplies a small
pull-up current to the load when the output switch is off. (A
100k resistor will draw 50
μ
A from a 5V supply.) Normally, the
load dominates, pulling OUT low. If the load is absent, the
optional resistor pulls OUT high, activating the fault flag if CTL
is off.
When a load is switched off with CTL, capacitance on the
output may cause the open-load function to pull the flag low
until the capacitor is discharged below approximately 2.4V.
Omit the pull-up resistor when open load detection is not
required and for minimum off-state supply current.
Power Bus Switch
The MIC2505/6 family features a MOSFET reverse current
flow prevention circuit. This prevents current from flowing
backwards (from OUT to IN) when CTL is disabled as long as
V
IN
is above UVLO minimum. In Figure 2, when U1 is on and
U2 is off, this feature prevents current flow from the load (5V)
backward through U2 to the 3.3V supply. (If a discrete
MOSFET and driver were used, the MOSFET’s internal body
diode would short the 5V load to the 3.3V supply.)
FLG will be active (low) on any switch that is off whenever the
load voltage is greater than the open load threshold (approxi-
mately 1V) except for MIC2505-1 and MIC2505-2.
Logic-High = 5V Output
U1
MIC2505BM
CTL
L
OUT
FLG
GND
OUT
GATE
IN
IN
+5V
1
8
2
7
3
6
4
5
0.1μF
U2
MIC2505BM
CTL
OUT
FLG
GND
OUT
GATE
IN
IN
1
8
2
7
3
6
4
5
+3.3V
0.1μF
1N4148
(optional)
Figure 2. 5V/3.3V Switch Concept
This circuit’s function would otherwise require a dual driver,
two MOSFETs, plus two diodes (or a dual driver plus four
MOSFETs).
Hot Plug-In Applications (Soft-Start)
The MIC2505/6 family can be used to protect the socket-side
and card-side of a supply circuit from transients caused when
a capacitive load is connected to an active supply.
The switch presents a high impedance when off, and slowly
becomes a low impedance as it turns on. This reduces the
inrush current and related voltage drop that result from
charging a capacitive load.
MIC2505BM
CTL
OUT
FLG
GND
OUT
GATE
IN
IN
1
8
2
7
3
6
4
5
0.1μF
Capacitive
Load
3.3V
Power Control
Circuitry
GND
Socket
Card
Figure 3. Hot Plug-In Concept
A gate capacitor may be added to the MIC2505 to slow the
turn on time even more, reducing the inrush current. See
“MIC2505 Turn-On Delay” graph. The UVLO feature insures
that each time the card is removed and V
IN
= 0 that the gate
of the output switch is discharged to zero volts. A controlled
turn-on is executed each time a board is plugged in, even with
multiple insertions.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2514BM5 | SWITCH SLIDE SPDT SILVR 5A RTANG |
| MIC2514 | IttyBitty⑩ Integrated High-Side Switch Preliminary Information |
| MIC2525 | Replaced by PT6523 : |
| MIC2525-1BM | Replaced by PT6523 : |
| MIC2525-1BN | USB Power Control Switch Not Recommended for New Designs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2506BM | 功能描述:IC SW HIGH SIDE DUAL 1A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 內部開關 系列:- 標準包裝:1 系列:- 類型:高端 輸入類型:非反相 輸出數:1 導通狀態電阻:85 毫歐 電流 - 輸出 / 通道:2A 電流 - 峰值輸出:6A 電源電壓:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:4-UFDFN 裸露焊盤，4-TMLF? 供應商設備封裝:4-TMLF?（1.2x1.6） 包裝:剪切帶 (CT) 其它名稱:576-1574-1 |
| MIC2506BM TR | 功能描述:IC SW DUAL 1A HIGH SIDE 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 內部開關 系列:- 標準包裝:1 系列:- 類型:高端 輸入類型:非反相 輸出數:1 導通狀態電阻:85 毫歐 電流 - 輸出 / 通道:2A 電流 - 峰值輸出:6A 電源電壓:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:4-UFDFN 裸露焊盤，4-TMLF? 供應商設備封裝:4-TMLF?（1.2x1.6） 包裝:剪切帶 (CT) 其它名稱:576-1574-1 |
| MIC2506YM | 功能描述:電源開關 IC - USB Fully Integrated High-Side Switch (Dual 1Amp) - Lead Free RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MIC2506YM TR | 功能描述:電源開關 IC - USB Fully Integrated High-Side Switch (Dual 1Amp) - Lead Free RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MIC2506YM | 制造商:Micrel Inc 功能描述:Analog Switch / Multiplexer (Mux) IC |
發布緊急采購，3分鐘左右您將得到回復。