參數資料
型號： MIC2310-2ZTS TR
廠商： Micrel Inc
文件頁數： 4/34頁
文件大小： 473K
描述： IC HOT SWAP CTLR 2CHAN 24TSSOP
標準包裝： 2,500
類型： 熱交換控制器
應用： 通用
內部開關： 無
電流限制： 可調
電源電壓： 10.8 V ~ 13.2 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 24-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 24-TSSOP
包裝： 帶卷 (TR)
Micrel, Inc.
MIC2310
 
 
July 2008 
4
M9999-070108-A
 
Pin Description 
Pin Number
Pin Name
Pin Function
1
UVLO
Undervoltage Lockout Input. When the applied voltage at the UVLO pin is higher
than the controllers V
UVLOH
 threshold voltage, the GATE drive circuits are active
when ENABLE= HIGH. If the applied voltage at the UVLO pin falls below the
controllers V
UVLOL
 threshold voltage, the GATE drive circuits are disabled to turn
the external MOSFET OFF. In addition, the DISCH circuit is activated to drive an
optional, external discharge transistor alone (illustrated in the Typical Application
circuit) or in combination with an SCR for a very fast discharge circuit
configuration.
2
OVP
Overvoltage Protection Input. When the applied voltage at the OVP pin is higher
than the controllers V
OVPH
 threshold voltage, the GATE drive circuit is disabled
to turn the external MOSFET OFF. In addition, the DISCH circuit is activated to
drive an optional, external discharge transistor alone (illustrated in the Typical
Application circuit) or in combination with an SCR for a very fast discharge circuit
configuration. Using an external resistor divider, the UVLO and the OVP pins
form a window comparator that defines the supply voltage range within which the
load may be safely powered.
3
VISS
Steady-state Output Current Monitor. This output signal provides an analog
voltage that is proportional to the steady-state load current. This signal is
provided as an input to the system supervisor/processor to monitor the dc
current/power level of the application circuit.
4
VREG
Internal +5V Regulator Bypass. Connect a 0.1-礔, 16V ceramic capacitor from
this pin to AGND.
5
NC
No connection
6
ENABLE
ENABLE Input. An active asserted-HIGH digital input that controls the operation
of the MIC2310. Activated after the internal POR timer has terminated, a LOW-
to-HIGH transition on this pin commences a start-up sequence if the applied V
CC
 
is above the V
UVLOH
 and below the V
OVPH
 threshold voltages. While ENABLE =
LOW, the GATE pin is held to 0V and the DISCH output is activated. The
ENABLE input can be used to reset the internal circuit breaker by applying a
HIGH-to-LOW-to-HIGH transition as defined by t
ENLPW
 following either a load
current fault, an open LOADSENSE fault, an open GNDSENSE fault, or a
shorted RSENSE fault.
7
S0
8
S1
Secondary OC Detector Current Threshold Digital Inputs  S1 is the MSB and
S0 is the LSB. When used together, S[1:0] sets the overcurrent threshold for the
secondary overcurrent detection circuit to one of four levels relative to the
primary overcurrent detector nominal threshold. For example, S[1:0] = L, L sets
the secondary overcurrent threshold at 1.3X; S[1:0] = L, H sets a 1.5X threshold;
S[1:0] = H, L sets a 2X threshold, and S[1:0] = H, H sets a 1.75X threshold. If the
S[1:0] pins are not connected or left NC, the default setting is S[1:0] = L, L or
1.3X. The permissible voltage range on these inputs is AGND d S[1:0] d V
CC
.
9
CRETRY
Auto-retry Timing Capacitor. A capacitor connected from the CRETRY pin to
AGND configures the MIC2310 to re-start automatically with ENABLE = HIGH
after the circuit breaker trips and latches off. It also sets the cool-off time delay
before a new load current start-up sequence is initiated. To configure the
MIC2310s circuit breaker to latch off after fault, connect this pin to AGND. The
circuit breaker latches OFF and remains latched OFF unless the ENABLE input
is toggled HIGH-to-LOW-to-HIGH as defined by t
ENLPW
 or the V
CC
 supply voltage
is turned OFF then ON.
10
CPRIMARY     Primary Overcurrent Detector Timing Capacitor. Connecting a capacitor from the
CPRIMARY pin to AGND sets the response time of the controllers primary
overcurrent detection circuit to GATE OFF in the event of an overcurrent
condition. If the CPRIMARY pin is not connected, the primary overcurrent
detection response time defaults to t
POCSENSE
, typically 250祍 as specified in the
Electrical Characteristics Table. The controller incorporates a patent-pending
built-in test for a faulty CPRIMARY capacitor.
相關PDF資料
PDF描述
MIC2341-2YTQ IC HOT PLUG CTLR DUAL PCI 48TQFP
MIC2569YQS TR IC POWER SWITCH CABLECARD 16QSOP
MIC2583R-MBQS TR IC CTRLR HOT SWAP 200MV 16-QSOP
MIC2585-2MBTS TR IC CTRLR HOT SWAP DUAL 24-TSSOP
MIC2586R-2BM TR IC CTRLR/SEQ HOT SWAP 14-SOIC
相關代理商/技術參數
參數描述
MIC23150-4YMT EV 功能描述:電源管理IC開發工具 2.0A 4MHz HyperLight Load Buck Regulator - Evaluation Board RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
MIC23150-4YMT TR 功能描述:直流/直流開關調節器 2.0A 4MHz HyperLight Load Buck Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MIC23150-4YMT-TR 功能描述:Buck Switching Regulator IC Positive Fixed 1.2V 1 Output 2A 8-VFDFN Exposed Pad, 8-MLF? 制造商:microchip technology 系列:HyperLight Load? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:固定 輸出數:1 電壓 - 輸入（最小值）:2.7V 電壓 - 輸入（最大值）:5.5V 電壓 - 輸出（最小值/固定）:1.2V 電壓 - 輸出（最大值）:- 電流 - 輸出:2A 頻率 - 開關:4MHz 同步整流器:是 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤，8-MLF? 供應商器件封裝:8-MLF?（2x2） 標準包裝:1
MIC23150-55YMT TR 功能描述:直流/直流開關調節器 2.0A 4MHz HyperLight Load Buck Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MIC23150-55YMT-TR 功能描述:Buck Switching Regulator IC Positive Fixed 1.35V 1 Output 2A 8-UFDFN 制造商:microchip technology 系列:HyperLight Load? 包裝:剪切帶（CT） 零件狀態:停產 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:固定 輸出數:1 電壓 - 輸入（最小值）:2.7V 電壓 - 輸入（最大值）:5.5V 電壓 - 輸出（最小值/固定）:1.35V 電壓 - 輸出（最大值）:- 電流 - 輸出:2A 頻率 - 開關:4MHz 同步整流器:是 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:8-UFDFN 供應商器件封裝:8-TDFN（2x2） 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*