- 您現在的位置：買賣IC網 > Datasheet目錄44 > MIC184BM TR (Micrel Inc)IC SUPERVISOR LOCAL/REMOTE 8SOIC Datasheet資料下載
參數資料
| 型號： | MIC184BM TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 11/20頁 |
| 文件大小： | 483K |
| 描述： | IC SUPERVISOR LOCAL/REMOTE 8SOIC |
| 標準包裝： | 2,500 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -55°C ~ 125°C，外部傳感器 |
| 精確度： | ±2°C 本地（最大），±3°C 遠程（最大） |
| 拓?fù)洌?/td> | ADC（三角積分型），寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | MIC184BMTR MIC184BMTR-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
May 2006
11
MIC184
MIC184
Micrel
MIC184s power consumption drops to 1礎 typical in shutdown
mode. All registers may be read from, or written to, while in
shutdown mode. Serial bus activity will slightly increase the
MIC184s power consumption.
Entering shutdown mode will not affect the state of INT when
the device is in comparator mode (MODE = 0). However, If
the device is shut down while in interrupt mode, the INT pin
will be deasserted and the internal latch (STS) holding the
interrupt status will be cleared. Therefore, no interrupts will
be generated while the MIC184 is in shutdown mode, and
the interrupt status will not be retained. It is important to
note, however, that the cause of the last temperature event
will be retained in the MIC184. This is described further in
Comparator and Interrupt Modes below. The diode fault
detection mechanism (see Diode Faults ) requires one or
more A/D conversion cycles to detect external sensor faults.
Hence, no diode faults will be detected while the device is
in shutdown.
Comparator and Interrupt Modes
Depending on the setting of the MODE bit in the congura-
tion register, the INT output will behave either as an interrupt
request signal or a thermostatic control signal. Thermostatic
operation is known as comparator mode. The INT output is
asserted whenever the measured temperature, as reported
in the TEMP register, exceeds the threshold programmed in
the T_SET register for the number of conversions specied by
Fault_Queue (described below). In comparator mode, INT will
remain asserted unless and until the measured temperature
falls below the value in the T_HYST register for Fault_Queue
conversions. No action on the part of the host is required for
operation in comparator mode. Note that entering shutdown
mode will not affect the state of INT when the device is in
comparator mode.
In interrupt mode, once a temperature event has caused STS
to be set, and the INT output to be asserted, they will not be
automatically deasserted when the measured temperature
falls below T_HYST. They can only be deasserted by reading
any of the MIC184's internal registers or by putting the device
into SHUTDOWN mode. If the most recent temperature event
was an overtemperature condition, STS will not be set again,
and INT cannot be reasserted, until the device has detected
that TEMP < T_HYST. Similarly, if the most recent temperature
event was an undertemperature condition, STS will in be set
again, and INT cannot be reasserted, until the device has
detected that TEMP > T_SET. This keeps the internal logic of
the MIC184 backward compatible with that of the LM75 and
similar devices. There is a software override for this: while
the MIC184 is operating in interrupt mode, the part can be
unconditionally set to monitor for an overtemperature condi-
tion, regardless of what caused the last temperature event.
This is done by clearing the MODE bit, and then immediately
resetting it to 1. Following this sequence the next temperature
event detected will be an overtemperature condition, regard-
less of whether the last temperature event was the result of
an overtemperature or undertemperature condition.
In both modes, the MIC184 will be responsive to overtem-
perature events upon power up.
Fault_Queue
A Fault_Queue (programmable digital lter) is provided in the
MIC184 to prevent false tripping due to thermal or electrical
noise. Two bits, CONFIG[4:3], set the depth of Fault_Queue.
Fault_Queue then determines the number of consecutive
temperature events (TEMP > T_SET or TEMP < T_HYST)
which must occur in order for the condition to be considered
valid. As an example, assume the MIC184 is in comparator
mode, and CONFIG[4:3] is programmed with 10
b
. Then the
measured temperature would have to exceed T_SET for four
consecutive A/D conversions before INT would be asserted
or the status bit set. Similarly, TEMP would have to be less
than T_HYST for four consecutive conversions before INT
would be reset.
Like any lter, the Fault_Queue function also has the effect of
delaying the detection of temperature events. In this example,
it would take 4 ?t
CONV
to detect a temperature event. The
depth of Fault_Queue vs. D[4:3] of the conguration register
is shown in Table 4.
Handling Interrupts
The MIC184 may be either polled by the host, or request the
hosts attention via the INT pin. In the case of polled opera-
tion, the host periodically reads the contents of CONFIG to
check the state of the status bit. The act of reading CONFIG
clears the status bit, STS. If more than one event that sets
the status bit occurs before the host polls the MIC184, only
the fact that at least one such event has occurred will be
apparent to the host.
If TEMP < T_HYST or TEMP > T_SET for Fault_Queue con-
versions, the status bit STS will be set in the CONFIG register.
This action cannot be masked. However, a temperature
event will only generate an interrupt signal on INT if inter-
rupts from the MIC184 are enabled (IM = 0 and MODE = 1
in the conguration register). Reading any register following
an interrupt will cause INT to be deasserted, and will clear
STS. The host should read the contents of the conguration
register after receiving an interrupt to conrm that the MIC184
was the source of the interrupt. This is shown in Figure 7.
As noted above, putting the device into shutdown mode will
also deassert INT and clear STS. Therefore, this usually
should not be done before completing the appropriate inter-
rupt service routine(s).
Since temperature-to-digital conversions continue while INT
is asserted, it is possible that temperature could change be-
tween the MIC184s assertion of its INT output and the hosts
response to the interrupt. It is good practice when servicing
interrupts for the host to read the current temperature to conrm
that the condition that caused the interrupt still exists.
]
3
:
4
[
G
I
F
N
O
C
h
t
p
e
D
e
u
e
u
Q
_
t
l
u
a
F
0
0
*
n
o
i
s
r
e
v
n
o
c
1
1
0
s
n
o
i
s
r
e
v
n
o
c
2
0
1
s
n
o
i
s
r
e
v
n
o
c
4
1
1
s
n
o
i
s
r
e
v
n
o
c
6
g
n
i
t
t
e
s
t
l
u
a
f
e
D
*
Table 4. Fault_Queue Depth Settings
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2086-MBQS TR | IC CTRLR HOW SWAP SGL 20-QSOP |
| MIC2225-4OYMT TR | IC REG DL BUCK/LINEAR 10TMLF |
| MIC2310-2ZTS TR | IC HOT SWAP CTLR 2CHAN 24TSSOP |
| MIC2341-2YTQ | IC HOT PLUG CTLR DUAL PCI 48TQFP |
| MIC2569YQS TR | IC POWER SWITCH CABLECARD 16QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC184YM | 功能描述:板上安裝溫度傳感器 Improved LM75 Series Local/Remote Temperature Sensor in SOIC-8 Lead-Free RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MIC184YM TR | 功能描述:板上安裝溫度傳感器 Improved LM75 Series Local/Remote Temperature Sensor in SOIC-8 Lead-Free RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MIC184YMM | 功能描述:板上安裝溫度傳感器 Improved LM75 Series Local/Remote Temperature Sensor in MSOP-8 Lead-Free RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MIC184YMM TR | 功能描述:板上安裝溫度傳感器 Improved LM75 Series Local/Remote Temperature Sensor in MSOP-8 Lead-Free RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MIC196 | 制造商:American DJ 功能描述:Laser Light Effect DMX Red Green and Blue Laser |
發布緊急采購，3分鐘左右您將得到回復。