- 您現在的位置：買賣IC網 > PDF目錄383602 > MH89760BN (Mitel Networks Corporation) Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 PDF資料下載
參數資料
| 型號： | MH89760BN |
| 廠商： | Mitel Networks Corporation |
| 元件分類： | 通信及網絡 |
| 英文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 中文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 文件頁數： | 6/38頁 |
| 文件大小： | 846K |
| 代理商： | MH89760BN |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
4-60
MH89760B
Preliminary Information
.
Table 1. Master Control Word 1 (Channel 15, CSTi0)
Table 2. Master Control Word 2 (Channel 31, CSTi0)
Bit
Name
Description
7
Debounce
When set the received A, B, C and D signalling bits are reported directly in the per
channel status words output at CSTo. When clear, the signalling bits are debounced for
6 to 9 ms before they are placed on CSTo.
Transparent Zero Code Suppression.
When this bit is set, no zero code suppression is
implemented.
Binary Eight Zero Suppression.
When this bit is set, B8ZS zero code suppression is
enabled. When clear, bit 7 in data channels containing all zeros is forced high before
being transmitted on the DS1 side. This bit is inactive if the TSPZCS bit is set.
8 kHz Output Select.
When set, the E8Ko pin is held high. When clear, the E8Ko
generates an 8 kHz output derived from the extracted 1.544 MHz clock or C1.5i clock
(see Pin Description for E8Ko).
External Control Pin.
When set, the XCtl pin is held high. When clear, XCtl is held low.
ESF Yellow Alarm.
Valid only in ESF mode. When set, a sequence of eight 1’s followed
by eight 0’s is sent in the FDL bit positions. When clear, the FDL bit contains data input at
the TxFDL pin.
When this bit is set, robbed bit signalling is disabled on all DS0 transmit channels. When
clear, A, B, C and D signalling bits are inserted into bit position 8 of all DS0 channels in
every 6th frame.
Yellow Alarm.
When set, bit 2 of all DS0 channels is set low. When clear, bit 2 operates
normally.
6
TSPZCS
5
B8ZS
4
8kHSel
3
2
XCtl
ESFYLW
1
Robbed bit
0
YLALR
Bit
Name
Description
7
RMLOOP
Remote Loopback.
When set, the data received at RxR and RxT is looped back to OUTB
and OUTA respectively. The data is clocked into the device with the extracted 1.544 MHz
clock. The device still monitors the received data and outputs it at DSTo. The device
operates normally when the bit is clear.
Digital Loopback.
When set, the data input on DSTi is looped around to DSTo. The
normal received data on RxR and RxT is ignored. However, the data input at DSTi is still
transmitted on OUTA and OUTB. The device frames up on the looped data using the C1.5i
clock.
All One’s Alarm.
When set, the chip transmits an unframed all 1's signal on OUTA and
OUTB.
ESF/D4 Select.
When set, the device is in ESF mode. When clear, the device is in D3/D4
mode.
Reframe.
If set for at least one frame and then cleared, the chip will begin to search for a
new frame position. Only the change from high to low will cause a reframe, not a
continuous low level.
SLC-96 Mode Select.
The chip is in SLC-96 mode when this bit is set. This enables input
and output of the F
S
bit pattern using the same pins as the facility data link in ESF mode.
The chip will use the same framing algorithm as D3/D4 mode. The user must insert the
valid F
S
bits in 2 out of 6 superframes to allow the receiver to find superframe sync, and
the transmitter to insert A and B bits in every 6th frame. The SLC-96 FDL completely
replaces the F
S
pattern in the outgoing S bit position. Inactive in ESF mode.
In ESF mode, when set, the chip disregards the CRC calculation during synchronization.
When clear, the device will check for a correct CRC before going into synchronization. In
D3/D4 mode, when set, the device will synchronize on the first correct S-bit pattern
detected. When this bit is clear, the device will not synchronize if it has detected more than
one candidate for the frame alignment pattern (i.e., a mimic).
Maintenance Mode.
When set, the device will declare itself out-of-sync if 4 out of 12
consecutive F
T
bits are in error. When clear, the out-of-sync threshold is 2 errors in 4 F
T
bits. In this mode, four consecutive bits following an errored F
T
bit are examined.
6
DGLOOP
5
ALL1'S
4
ESF/D4
3
ReFR
2
SLC-96
1
CRC/MIMIC
0
Maint.
相關PDF資料 |
PDF描述 |
|---|---|
| MH89760BS | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MH89761 | T1 Transmit Equalizer Advance Information |
| MH89770N | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MH89770 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MH89770S | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MH89760BS | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ST-BUS⑩ FAMILY T1/ESF Framer & Interface Preliminary Information |
| MH89761 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1 Transmit Equalizer Advance Information |
| MH89770 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/ESF Framer & Interface Preliminary Information |
| MH89770N | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/ESF Framer & Interface Preliminary Information |
| MH89770S | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/ESF Framer & Interface Preliminary Information |
發布緊急采購，3分鐘左右您將得到回復。