- 您現在的位置：買賣IC網 > Datasheet目錄44 > MCZ34652EFR2 (Freescale Semiconductor)IC HOTSWAP CTRLR 2A NEG 16SOIC Datasheet資料下載
參數資料
| 型號： | MCZ34652EFR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 18/26頁 |
| 文件大?。?/td> | 1802K |
| 描述： | IC HOTSWAP CTRLR 2A NEG 16SOIC |
| 標準包裝： | 2,500 |
| 類型： | 熱交換開關 |
| 應用： | 通用 |
| 內部開關： | 是 |
| 電流限制： | 2A |
| 電源電壓： | 15 V ~ 80 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC N |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
Analog Integrated Circuit Device Data
18
Freescale Semiconductor
34652
TYPICAL APPLICATIONS
rchived by Freescale Semiconductor, Inc., 2008
TYPICAL APPLICATIONS
The 34652 resides on the plug-in board (see Figures 18
and 19
), allowing the board to be safely inserted or removed
without damaging electrical equipment. The 34652 can be
operated with no external components other than the power
good output signal pull-up resistor if the default mode was
selected for all the programmable features. This is one of the
great advantages of the 34652: it operates with minimal user
interface and minimal external component count and still
offers complete hot swapping functionality with all the
necessary protection features, from undervoltage/
overvoltage detection, to current limiting, to short circuit
protection and power good output signaling. The default
values were chosen to be sufficient for many standard
applications.
Figure 18
is a typical application diagram depicting the
default mode and using the power good output signal pull-up
resistor. Refer to the static and dynamic electrical
characteristics tables on pages 6
through 9
for the various
default values.
Figure 18. Typical Application Diagram with Default
Settings and Minimal External Components
The 34652 can be also programmed for different values of
the Overcurrent Limit, the Charging Current Limit, the Start-
Up and Retry Delay Timer, and the UV / OV detection
thresholds using external components connected to the
device. Figure 19
shows the 34652 with the required external
components that allow access to all programmable features
in the device.
Figure 19. Typical Application Diagram with External
Components Necessary to Program the Device
UNDERVOLTAGE AND OVERVOLTAGE
DETECTION
The UV and OV pins are used to monitor the input voltage
to ensure that it is within the operating range and that there
are no overvoltage or undervoltage conditions, and to quickly
turn off the Power MOSFET if there are. The pins are
connected to internal comparators that compare the voltages
at the UV and OV pins with a reference voltage. The UV and
OV pins can be left unconnected for the default threshold
values of their trip point or the user can set the threshold
values externally with a simple voltage divider using resistors
between VPWR and VIN (resistors R
1
, R
2
, and R
3
in
Figure 19
). For the default mode, the 34652 is equipped with
an internal resistor divider that acts the same as the external
one. The typical default values of 37 V for the UV turn-off
threshold (falling threshold) and 78 V for the OV turn-off
threshold (rising threshold) will give a typical operating range
of 38 V to 76 V. This range is suitable for telecom industry
standards.
When the device passes the UVLO threshold, it checks if
there is any external resistor divider connected to the OV and
UV pins. If there is, it determines the value of the UV/OV
thresholds accordingly. If there is not, it defaults to the
internal resistor divider. It then uses the UV/OV detection
circuits to check the input supply levels before turning on the
Power MOSFET during the Start-Up Timer delay and
thereafter. As long as the voltage on the UV pin is above its
falling threshold and the voltage on the OV pin is below its
rising threshold, the supply is within operating range and the
Power MOSFET is allowed to turn on and stay on. If the UV
pin drops below its falling threshold or the OV pin rises above
its rising threshold, then one of the start-up conditions (refer
to page
12
for list) is violated and the Power MOSFET turns
off, the power good signals deactivate, and a new start-up
VPWR
UV
VIN
TIMER ICHG ILIM
VOUT
(2)
PG
PG
33652
(4)
GND
-48 V
DC/DC
Converter
Application
Dependent
Enable/Enable
C
LOAD
44 k?/DIV>
PLUG-IN CARD
DISABLE
OV
VPWR
UV
VIN
TIMER ICHG ILIM
VOUT
(2)
PG
33652
(4)
GND
-48 V
DC/DC
Converter
Application
Dependent
Enable/Enable
C
LOAD
44 k?/DIV>
PLUG-IN CARD
DISABLE
OV
R
2
R
1
R
3
PG
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ34653EFR2 | IC HOTSWAP CTRLR 1A NEG 8-SOIC |
| MCZ34670EG | IC POE CURR MODE SW REG 20-SOIC |
| MIC184BM TR | IC SUPERVISOR LOCAL/REMOTE 8SOIC |
| MIC2086-MBQS TR | IC CTRLR HOW SWAP SGL 20-QSOP |
| MIC2225-4OYMT TR | IC REG DL BUCK/LINEAR 10TMLF |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ34652EFR2SCALE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:2.0 A Negative Voltage Hot Swap Controller with Enhanced Programmability |
| MCZ34653EF | 功能描述:熱插拔功率分布 Hot Swap Controller 1.0 Neg Vltg RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MCZ34653EF/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:1.0 A Negative Voltage Hot Swap Controller |
| MCZ34653EFR2 | 功能描述:熱插拔功率分布 Hot Swap Controller 1.0 Neg Vltg RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MCZ34670EG | 功能描述:熱插拔功率分布 POWER OVER ETHERNET RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。