- 您現在的位置：買賣IC網 > PDF目錄11712 > MCZ33904B3EKR2 (Freescale Semiconductor)IC SBC CAN HS 3.3V 32SOIC PDF資料下載
參數資料
| 型號： | MCZ33904B3EKR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 92/106頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SBC CAN HS 3.3V 32SOIC |
| 標準包裝： | 1,000 |
| 應用： | 系統基礎芯片 |
| 接口： | CAN，LIN |
| 電源電壓： | 5.5 V ~ 28 V |
| 封裝/外殼： | 32-BSOP（0.295"，7.50mm 寬）裸露焊盤 |
| 供應商設備封裝： | 32-SOICW 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁當前第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
Analog Integrated Circuit Device Data
86
Freescale Semiconductor
33903/4/5
SERIAL PERIPHERAL INTERFACE
FLAGS AND DEVICE STATUS
CAN
CAN driver
state
Description
Report real time CAN bus driver state: 1 if Driver is enable, 0 if driver disable
Set / Reset condition
Set: CAN driver is enable. Reset: CAN driver is disable. Driver can be disable by SPI command (ex
CAN set in RXD only mode) or following a failure event (ex: TXD Dominant). Flag read SPI command
(0x2180) do not clear the flag, as it is “real time” information.
CAN receiver
state
Description
Report real time CAN bus receiver state: 1 if Enable, 0 if disable
Set / Reset condition
Set: CAN bus receiver is enable. Reset: CAN bus receiver is disable. Receiver disable by SPI
command (ex: CAN set in sleep mode). Flag read SPI command (0x2180) do not clear the flag, as it
is “real time” information.
CAN WU
enable
Description
Report real time CAN bus Wake-up receiver state: 1 if WU receiver is enable, 0 if disable
Set / Reset condition
Set: CAN Wake-up receiver is enable. Reset: CAN Wake-up receiver is disable. Wake-up receiver is
controlled by SPI, and is active by default after device Power ON. SPI command (0x2180) do not
change flag state.
CAN
Wake-up
Description
Report that Wake-up source is CAN
Set / Reset condition
Set: after CAN wake detected. Reset: Flag read (SPI)
CAN
Overtemp
Description
Report that the CAN interface has reach overtemperature threshold.
Set / Reset condition
Set: CAN thermal sensor above threshold. Reset: thermal sensor below threshold and flag read (SPI)
RXD low(50)
Description
Report that RXD pin is shorted to GND.
Set / Reset condition
Set: RXD low failure detected. Reset: failure recovered and flag read (SPI)
Rxd high
Description
Report that RXD pin is shorted to recessive voltage.
Set / Reset condition
Set: RXD high failure detected. Reset: failure recovered and flag read (SPI)
TXD dom
Description
Report that TXD pin is shorted to GND.
Set / Reset condition
Set: TXD low failure detected. Reset: failure recovered and flag read (SPI)
Bus Dom
clamp
Description
Report that the CAN bus is dominant for a time longer than tDOM
Set / Reset condition
Set: Bus dominant clamp failure detected. Reset: failure recovered and flag read (SPI)
CAN
Overcurrent
Description
Report that the CAN current is above CAN overcurrent threshold.
Set / Reset condition
Set: CAN current above threshold. Reset: current below threshold and flag read (SPI)
CAN_UF
Description
Report that the CAN failure detection has not yet identified the bus failure
Set / Reset condition
Set: bus failure pre detection. Reset: CAN bus failure recovered and flag read
CAN_F
Description
Report that the CAN failure detection has identified the bus failure
Set / Reset condition
Set: bus failure complete detetction.Reset: CAN bus failure recovered and flag read
CANL
to VBAT
Description
Report CAN L short to VBAT failure
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
CANL to VDD
Description
Report CANL short to VDD
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
CANL to GND Description
Report CAN L short to GND failure
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
CANH
to VBAT
Description
Report CAN H short to VBAT failure
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
CANH to VDD
Description
Report CANH short to VDD
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
CANH to
GND
Description
Report CAN H short to GND failure
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
Notes
50.
Not available on “C” versions
Table 40. Flag Descriptions
Flag
Description
相關PDF資料 |
PDF描述 |
|---|---|
| C8051F983-GM | IC MCU 8BIT 4KB FLASH 20QFN |
| MCZ33904B3EK | IC SBC CAN HS 3.3V 32SOIC |
| D38999/26MC98SN | CONN PLUG 10POS STRAIGHT W/SCKT |
| MS27484T16B26S | CONN PLUG 26POS STRAIGHT W/SCKT |
| MCZ33903B5EKR2 | IC SBC CAN HS 5.0V 32SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33904B3R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:SBC Gen2 with CAN High Speed and LIN Interface |
| MCZ33904B5EK | 功能描述:CAN 接口集成電路 5V SBC HI SPEED CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MCZ33904B5EKR2 | 功能描述:CAN 接口集成電路 5V SBC HSCAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MCZ33904B5R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:SBC Gen2 with CAN High Speed and LIN Interface |
| MCZ33904C3EK | 功能描述:CAN 接口集成電路 3.3V SBC HSCAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。