參數資料
型號： MCZ33800EK
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Engine Control Integrated Circuit
中文描述： 發動機控制集成電路
文件頁數： 16/39頁
文件大?。?/td> 461K
代理商： MCZ33800EK
Analog Integrated Circuit Device Data
Freescale Semiconductor
16
33800
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
ANALOG VOLTAGE SUPPLY (VPWR)
The VPWR pin is battery input to the 33800 IC. The VPWR
pin requires external reverse battery and transient protection.
Maximum input voltage on VPWR is 45V. All IC analog
current and internal logic current is provided from the VPWR
pin. With V
DD
and EN applied to the IC, the application of
V
PWR
will perform a Power-ON Reset (
POR
).
DIGITAL VOLTAGE SUPPLY (VDD)
The VDD input pin is used to determine communication
logic levels between the microprocessor and the 33800
device. Current from V
DD
is used to drive SO output and pull-
up current for CS. V
DD
must be applied for Normal Mode
operation. Removing V
DD
from the IC will place the device in
Sleep Mode. Power-ON Reset will be performed with the
application of V
DD
supply
.
GROUND (GND)
The GND pin provides a low current analog ground for the
IC. The VPWR and VDD supplies are both referenced to the
GND pin. GND pin should be used for decoupling both
supplies.
CONSTANT CURRENT DRIVER GROUND
(CCDX_GND)
The Constant Current Driver Ground (CCDX_GND) pins
provide dedicated grounds for the Constant Current output
drivers. Both CCDX_GND1 and CCDX_GND2 grounds are
isolated from the other grounds of the IC.
GROUND (PGND1 - 3, CCD1_GND, CCD2_GND)
There are three PGND pins associated with the OSS
drivers. OUT1 driver and OUT2 driver have dedicated
PGND1 & PGND2 pins. Drivers OUT3 through Driver OUT8
share one PGND3 pin. In general all ground pins must be
connected together and terminated to ground on the circuit
board.
SOURCE VOLTAGE SENSE (VSSNS123
,
VSSNS456)
The Source Sense Ground pins (VSSNS123, VSSNS456)
provide dedicated grounds for the hex MOSFET pre-drivers.
The pins are used by the IC to monitor the drain to source
voltage of the external MOSFET. This pin must be connected
to the source of the external MOSFET and system ground.
VSSNS123 and VSSNS456 ground pins are isolated from
other internal IC grounds.
SERIAL CLOCK INPUT (SCLK)
The system clock (SCLK) pin clocks the internal shift
register of the 33800. The SI data is latched into the input
shift register on the rising edge of SCLK signal. The SO pin
shifts status bits out on the falling edge of SCLK. The SO data
is available for the MCU to read on the rising edge of SCLK.
With CS in a logic high state, signals on the SCLK and SI pins
will be ignored and the SO pin is tri-state.
CHIP SELECT (CS)
The system MCU selects the 33800 to receive
communication using the chip select (CS) pin. With the CS
in
a logic low state, command words may be sent to the 33800
via the serial input (SI) pin, and status information is received
by the MCU via the serial output (SO) pin. The falling edge of
CS enables the SO output and transfers status information
into the SO buffer.
Rising edge of the CS initiates the following operation:
1. Disables the SO driver (high-impedance)
2. Activates the received command word, allowing the
33800 to activate/deactivate output drivers.
To avoid any spurious data, it is essential the high-to-low
and low-to-high transitions of the CS signal occur only when
SCLK is in a logic low state. Internal to the 33800 device is an
active pull-up to VDD on CS. In cases were voltage exists on
CS without the application of V
DD
, no current will flow from
CS to the VDD pin.
SERIAL INPUT DATA (SI)
The SI pin is used for serial instruction data input. SI
information is latched into the input register on the rising edge
of SCLK. A logic high state present on SI will program a
one
in the command word on the rising edge of the CS signal. To
program a complete word, 16-bits of information must be
entered into the device.
SERIAL OUTPUT DATA (SO)
The SO pin is the output from the shift register. The SO pin
remains tri-stated until the CS pin transitions to a logic low
state. All normal operating drivers are reported as zero, all
faulted drivers are reported as one. The negative transition of
CS enables the SO driver.
The SI / SO shifting of the data follows a first-in-first-out
protocol, with both input and output words transferring the
most significant bit (MSB) first.
ENABLE (EN)
The ENABLE pin is an active high digital input pin used to
enable the device. With the EN pin low the device is in Sleep
Mode. With the EN pin high, the device is in Normal Mode
(V
DD
and V
PWR
applied). Exit from Sleep Mode initiates a
相關PDF資料
PDF描述
MCZ33879AEK Configurable Octal Serial Switch with Open Load Detect Current Disable
MCZ33880EG Configurable Octal Serial Switch with Serial Peripheral Interface I/O
MCZ33883EG H-Bridge Gate Driver IC
MCZ33884EG Switch Monitor Interface
MCZ33887EK 5.0 A H-Bridge with Load Current Feedback
相關代理商/技術參數
參數描述
MCZ33800EKR2 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33800R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit
MCZ33810EK 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33810EK/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC
MCZ33810EKR2 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*