LOGIC COMMANDS AND REGISTERS Figure 13. Requ" />
參數資料
型號： MCZ33784EF
廠商： Freescale Semiconductor
文件頁數： 14/30頁
文件大?。?/td> 0K
描述： IC SENSOR DBUS DSI 2.02 16-SOIC
標準包裝： 48
類型： 傳感器接口
輸入類型： 模擬
輸出類型： 數字
接口： 總線
電流 - 電源： 4mA
安裝類型： 表面貼裝
封裝/外殼： 16-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 16-SOIC N
包裝： 管件
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
33784
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Figure 13. Request AN1 Command and Response Format
I/O CONTROL COMMAND AND RESPONSE
This command can be used to configure the direction of
the I/O pins, and force their states if configured as outputs.
Refer to Figure 14 for the command and response format.
The response is sent during the next message following a
valid I/O Control command to the addressed device. Because
this is a long-word only command, there is no short word
response.
The direction (DR) bits are used to specify the direction
(input or output) of each pin independently. If the DR bit for a
specific I/O pin is set to 1, then that I/O pin will be an output
and the state of the level (Lx) bit will determine whether the
pin is driven high or low. If the DR bit for a specific I/O pin is
set to 0, then that pin will be an input and the Lx bit in the
command will have no affect on the state of the pin.
In the response to the I/O Control Command, the DR bits
will show the direction that the pins were programmed. The
Lx bits will have the values that were set in the command.
These values may not reflect the actual states of the pins. To
obtain the accurate states of the pins, the Request Status
Command should be used.
The 33784 will only act on the I/O Control Command if the
address bits in the command match with the address that the
device was initialized. If the addresses do not match, the
device will do nothing and no response will be generated.
Address ‘0000’ is a global command. All slaves in the
signal path will configure their I/O pins according to the state
of the data bits. No response results from the I/O control
global command.
Data
Address
Command
Word Type
––––––––
A3
A2
A1
A0
0101
LW & ELW
A3
A2
A1
A0
0101
SW & ESW (8-bit)
––
A3
A2
A1
A0
0101
ESW (10-bit)
Response
Word Type
A3
A2
A1
A0
0000
B9
B8
B7
B6
B5
B4
B3
B2
LW & ELW
B9
B8
B7
B6
B5
B4
B3
B2
SW & ESW (8-bit)
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
ESW (10-bit)
Legend
A[3:0] = Address bits. The address of the selected device.
An address value of 0000 is ignored by all devices.
“–” = Don’t care bit. Can be 0 or 1.
B[9:0] = Measured value.
相關PDF資料
PDF描述
VE-JNR-IZ-B1 CONVERTER MOD DC/DC 7.5V 25W
MCZ33793AEFR2 IC DSI SLAVE SENSOR 16-SOIC
MCZ33793AEF IC DSI SLAVE SENSOR 16-SOIC
VE-JNR-IY-F4 CONVERTER MOD DC/DC 7.5V 50W
MC908JB16JDWE IC MCU 16K FLASH 6MHZ USB 20SOIC
相關代理商/技術參數
參數描述
MCZ33784EF/R2- 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:DSI 2.02 Sensor Interface
MCZ33784EFR2 功能描述:加速計 - 板上安裝 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
MCZ33789AE 功能描述:網絡控制器與處理器 IC Airbag ASSP RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33789AE/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Airbag System Basis Chip (SBC) with Power Supply and PSI5 Sensor Interface
MCZ33789AER2 功能描述:網絡控制器與處理器 IC Airbag ASSP RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*