參數資料
型號： MCP6002ISN
廠商： Microchip Technology Inc.
元件分類： FPGA
英文描述： 200000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
中文描述： 1 MHz帶寬低功耗運算放大器
文件頁數： 8/24頁
文件大小： 553K
代理商： MCP6002ISN
MCP6001/2/4
DS21733D-page 8
2003 Microchip Technology Inc.
3.4
Supply Bypass
With this family of operation amplifiers, the power sup-
ply pin (V
DD
for single supply) should have a local
bypass capacitor (i.e., 0.01 μF to 0.1 μF) within 2 mm
for good high frequency performance. It also needs a
bulk capacitor (i.e., 1 μF or larger) within 100 mm to
provide large, slow currents. This bulk capacitor can be
shared with other parts.
3.5
PCB Surface Leakage
In applications where low input bias current is critical,
PCB (printed circuit board) surface leakage effects
need to be considered. Surface leakage is caused by
humidity, dust or other contamination on the board.
Under low humidity conditions, a typical resistance
between nearby traces is 10
12
. A 5V difference would
cause 5 pA, if current-to-flow; this is greater than the
MCP6001/2/4 family’s bias current at 25°C (1 pA, typ).
The easiest way to reduce surface leakage is to use a
guard ring around sensitive pins (or traces). The guard
ring is biased at the same voltage as the sensitive pin.
An example of this type of layout is shown in
Figure 3-4.
FIGURE 3-4:
for Inverting Gain.
Example Guard Ring Layout
1.
Non-inverting Gain and Unity Gain Buffer:
a.
Connect the non-inverting pin (V
IN
+) to the
input with a wire that does not touch the pcb
surface.
b.
Connect the guard ring to the inverting input
pin (V
IN
–). This biases the guard ring to the
common mode input voltage.
Inverting and Transimpedance Gain Amplifiers
(convert current to voltage, such as photo detec-
tors):
a.
Connect the guard ring to the non-inverting
input pin (V
IN
+). This biases the guard ring
to the same reference voltage as the op
amp (e.g., V
DD
/2 or ground).
b.
Connect the inverting pin (V
IN
–) to the input
with a wire that does not touch the PCB
surface.
2.
3.6
Application Circuits
3.6.1
UNITY GAIN BUFFER
The rail-to-rail input and output capability of the
MCP6001/2/4 op amp is ideal for unity-gain buffer
applications. The low quiescent current and wide band-
width makes the device suitable for a buffer configura-
tion in an instrumentation amplifier circuit, as shown in
Figure 3-5.
FIGURE 3-5:
with Unity Gain Buffer Inputs.
Instrumentation Amplifier
3.6.2
ACTIVE LOW-PASS FILTER
The MCP6001/2/4 op amp’s low input bias current
makes it possible for the designer to use larger resis-
tors and smaller capacitors for active low-pass filter
applications. However, as the resistance increases, the
noise generated also increases. Parasitic capacitances
and the large value resistors could also modify the fre-
quency response. These trade-offs need to be
considered when selecting circuit elements.
It is possible to have a filter cutoff frequency as high as
1/10th of the op amp bandwidth (100 kHz). Figure 3-6
shows a second-order butterworth filter with 100 kHz
cutoff frequency and a gain of +1V/V.
The
Microchip’s FilterLab
software.
component
values
were
selected
using
FIGURE 3-6:
Pass Filter.
Active Second-Order Low-
Guard Ring
V
SS
V
IN
-
V
IN
+
V
IN1
R
2
MCP6002
1/2
V
IN2
R
2
MCP6002
+
V
REF
MCP6001
+
V
OUT
R
1
R
1
-
+
-
-
1/2
V
OUT
V
IN2
V
IN1
–
(
)
R
1
R
2
-----
V
REF
+
=
R
1
= 20 k
R
2
= 10 k
14.3 k
MCP6002
-
V
OUT
53.6 k
100 pF
V
IN
33 pF
+
相關PDF資料
PDF描述
MCP6002IST 1 MHz Bandwidth Low Power Op Amp
MCP6004 1 MHz Bandwidth Low Power Op Amp
MCP6004E 200000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
MCP6004EMS 1 MHz Bandwidth Low Power Op Amp
MCP6004EP 200000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
相關代理商/技術參數
參數描述
MCP6002IST 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1 MHz Bandwidth Low Power Op Amp
MCP6002T-E/LT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1 MHz, Low-Power Op Amp
MCP6002T-E/MC 功能描述:運算放大器 - 運放 Dual 1.8V 1MHz OP, E temp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MCP6002T-E/MS 功能描述:運算放大器 - 運放 Dual 1.8V 1MHz RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MCP6002T-E/OT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1 MHz, Low-Power Op Amp
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*