I2C General Call Commands
參數資料
型號: MCP4728T-E/UN
廠商: Microchip Technology
文件頁數: 25/33頁
文件大?。?/td> 0K
描述: IC DAC 12BIT W/I2C 10-MSOP
視頻文件: MCP4728 Evaluation Board Demo
標準包裝: 2,500
設置時間: 6µs
位數: 12
數據接口: EEPROM,I²C,串行
轉換器數目: 4
電壓電源: 單電源
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-MSOP
包裝: 帶卷 (TR)
輸出數目和類型: 4 電壓,單極
采樣率(每秒): *
配用: MCP4728EV-ND - BOARD EVAL 12BIT 4CH DAC MCP4728
2010 Microchip Technology Inc.
DS22187E-page 31
MCP4728
5.4
I2C General Call Commands
The device acknowledges the general call address
command (0x00 in the first byte). The meaning of the
general call address is always specified in the second
byte. The I2C specification does not allow the use of
“00000000” (00h) in the second byte. Refer to the
Philips I2C document for more details of the General
Call specifications.
The MCP4728 device supports the following I2C
General Calls:
General Call Reset
General Call Wake-Up
General Call Software Update
General Call Read Address Bits
5.4.1
GENERAL CALL RESET
The
General Call Reset occurs if the second byte is
“00000110” (06h). At the acknowledgement of this
byte, the device will abort the current conversion and
perform the following tasks:
Internal Reset similar to a Power-on Reset (POR).
The contents of the EEPROM are loaded into
each DAC input and output registers immediately
VOUT will be available immediately regardless of
the LDAC pin condition
FIGURE 5-3:
General Call Reset.
5.4.2
GENERAL CALL WAKE-UP
If the second byte is “00001001” (09h), the device will
reset the Power-Down bits (PD1, PD0 = 0,0).
FIGURE 5-4:
General Call Wake-Up.
1st Byte
Note 1
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Stop
Start
2nd Byte
ACK (
MCP4728)
(General Call Command)
(Command Type = General Call Reset)
Clock Pulse (CLK Line)
Data (SDA Line)
Note 1: At this falling edge of the last ACK clock bit:
a. Startup Timer starts a reset sequence and
b. EEPROM data is loaded into the DAC Input and Output Registers immediately.
1st Byte
Note 1
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Stop
Start
2nd Byte
ACK (
MCP4728)
(General Call Command)
(Command Type = General Call Wake-Up)
Clock Pulse (CLK Line)
Data (SDA Line)
Note 1: Resets Power-Down bits at this falling edge of the last ACK clock bit.
相關PDF資料
PDF描述
MCP4822T-E/MS IC DAC 12BIT DUAL W/SPI 8MSOP
MCP4912T-E/SL DAC 10BIT DUAL SPI 14SOIC
MCP4921-E/MC DAC 12BIT SGL W/SPI 8DFN
MCP79402T-I/MNY IC RTCC 64BIT SRAM I2C 8TDFN
MCP7940MT-I/ST IC RTCC I2C 64B SRAM 8-TSSOP
相關代理商/技術參數
參數描述
MCP4729-E/SS 功能描述:數模轉換器- DAC Octal 12-bit NV DAC with I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP47A1T-A0E/LT 功能描述:數模轉換器- DAC 6-Bit Volatile DAC with Command Code RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP47A1T-A1E/LT 功能描述:數模轉換器- DAC 6-Bit Volatile DAC with Command Code RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP47DA1T-A0E/OT 功能描述:數模轉換器- DAC 6-bit windowed DAC voltage margining RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP47DA1T-A1E/OT 功能描述:數模轉換器- DAC 6-bit windowed DAC voltage margining RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube