- 您現在的位置：買賣IC網 > PDF目錄9445 > MCP4012T-503E/CH (Microchip Technology)IC DGTL POT 50K 1CH RHEO SOT23-6 PDF資料下載
參數資料
| 型號： | MCP4012T-503E/CH |
| 廠商： | Microchip Technology |
| 文件頁數： | 21/54頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DGTL POT 50K 1CH RHEO SOT23-6 |
| 標準包裝： | 1 |
| 接片： | 64 |
| 電阻（歐姆）： | 50k |
| 電路數： | 1 |
| 溫度系數： | 標準值 150 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | 2 線串行（芯片選擇，增/減） |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-6 |
| 供應商設備封裝： | SOT-23-6 |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 674 (CN2011-ZH PDF) |
| 其它名稱： | MCP4012T-503E/CHDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
MCP4011/2/3/4
DS21978C-page 28
2006 Microchip Technology Inc.
4.2
Power-up
When the device powers up (rising VDD crosses the
Trip Point Voltage (VTP)), the “default” wiper setting is
restored. Table 4-1 shows the default value loaded into
the wiper on POR/BOR.
TABLE 4-1:
DEFAULT POR WIPER
SETTING SELECTION
While VDD < Vmin (1.8V), the electrical performance
may not meet the data sheet specifications (see
Figure 4-2). The wiper state may be unknown. Also, the
device may be capable of incrementing or decrement-
ing, if a valid command is detected on the CS and U/D
pins.
4.3
Brown Out
If the device VDD is below the specified minimum
voltage, care must be taken to ensure that the CS and
U/D pins do not “create” any of the serial commands.
When the device VDD drops below VMIN (1.8V), the
electrical performance may not meet the data sheet
specifications (see Figure 4-2). The wiper state may be
unknown. Also, the device may be capable of
incrementing or decrementing, if a valid command is
detected on the CS and U/D pins.
When the device voltage rises from below the power-
up trip point (VTP) into the valid operation voltage
range, the wiper state will be forced to the default POR
wiper setting (see Table 4-1).
4.4
Serial Interface Inactive
The serial interface is inactive any time the CS pin is at
VIH and all write cycles are completed.
FIGURE 4-2:
Power-up and Brown-out.
Package
Code
Default
POR
Wiper
Setting
Wiper
Code
Typical
RAB Value
-202
Mid-scale
1Fh
2.1 k
Ω
-502
Mid-scale
1Fh
5.0 k
Ω
-103
Mid-scale
1Fh
10.0 k
Ω
-503
Mid-scale
1Fh
50.0 k
Ω
VTP
VSS
VDD
1.8V
POR Trip Point (on Rising VDD)
Outside Device Operation
Wiper Forced to Default POR Setting
相關PDF資料 |
PDF描述 |
|---|---|
| IDTQS3244QG | IC BUS QUICKSWITCH 8BIT 20QSOP |
| IDTQS3384QG | IC BUS SWITCH 10BIT HS 24QSOP |
| VE-B4Y-MY-S | CONVERTER MOD DC/DC 3.3V 33W |
| VE-B3Y-MY-S | CONVERTER MOD DC/DC 3.3V 33W |
| MCP4013T-103E/CH | IC DGTL POT 10K 1CH SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP4013 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low-Cost 64-Step Volatile Digital POT |
| MCP4013-103E/CH | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low-Cost 64-Step Volatile Digital POT |
| MCP4013-103E/MC | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low-Cost 64-Step Volatile Digital POT |
| MCP4013-103E/MS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low-Cost 64-Step Volatile Digital POT |
| MCP4013-103E/OT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low-Cost 64-Step Volatile Digital POT |
發布緊急采購，3分鐘左右您將得到回復。