參數資料
型號： MCP3901EV-MCU16
廠商： Microchip Technology
文件頁數： 18/30頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR 2CH ADC MCP3901
產品培訓模塊： MCP3901 Analog Front End
視頻文件： MCP3901 ADC Evaluation Board for 16-bit MCUs
標準包裝： 1
ADC 的數量： 2
位數： 24
數據接口： SPI?
輸入范圍： ±1 V
工作溫度： -40°C ~ 85°C
已用 IC / 零件： MCP3901
已供物品： 板
產品目錄頁面： 672 (CN2011-ZH PDF)
PCA2002
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 25 November 2011
25 of 30
NXP Semiconductors
PCA2002
32 kHz watch circuit with programmable output period and pulse width
14.3.2 Quality of solder joint
A flip-chip joint is considered to be a good joint when the entire solder land has been
wetted by the solder from the bump. The surface of the joint should be smooth and the
shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps
after reflow can occur during the reflow process in bumps with high ratio of bump diameter
to bump height, i.e. low bumps with large diameter. No failures have been found to be
related to these voids. Solder joint inspection after reflow can be done with X-ray to
monitor defects such as bridging, open circuits and voids.
14.3.3 Rework
In general, rework is not recommended. By rework we mean the process of removing the
chip from the substrate and replacing it with a new chip. If a chip is removed from the
substrate, most solder balls of the chip will be damaged. In that case it is recommended
not to re-use the chip again.
Device removal can be done when the substrate is heated until it is certain that all solder
joints are molten. The chip can then be carefully removed from the substrate without
damaging the tracks and solder lands on the substrate. Removing the device must be
done using plastic tweezers, because metal tweezers can damage the silicon. The
surface of the substrate should be carefully cleaned and all solder and flux residues
and/or underfill removed. When a new chip is placed on the substrate, use the flux
process instead of solder on the solder lands. Apply flux on the bumps at the chip side as
well as on the solder pads on the substrate. Place and align the new chip while viewing
with a microscope. To reflow the solder, use the solder profile shown in application note
AN10365 “Surface mount reflow soldering description”.
14.3.4 Cleaning
Cleaning can be done after reflow soldering.
相關PDF資料
PDF描述
RBC12DRTH-S93 CONN EDGECARD 24POS DIP .100 SLD
MLG1005SR18J INDUCTOR MULTILAYER 180NH 0402
RBC10DRES-S93 CONN EDGECARD 20POS .100 EYELET
GEC18DRTS-S93 CONN EDGECARD 36POS DIP .100 SLD
HBC06DRYN-S93 CONN EDGECARD 12POS DIP .100 SLD
相關代理商/技術參數
參數描述
MCP3901-I/SS 功能描述:開關變換器、穩壓器與控制器 Dual Ch Enrgy Metr FrntEnd SPI Intrface RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
MCP3901T-I/SS 功能描述:開關變換器、穩壓器與控制器 Dual Ch Enrgy Metr FrntEnd SPI Intrface RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
MCP3903 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Six Channel Delta Sigma A/D Converter
MCP3903-E/SS 功能描述:模數轉換器 - ADC 6CH Energy Meter Fr End SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MCP3903-E/SS 制造商:Microchip Technology Inc 功能描述:; Leaded Process Compatible:Yes; Peak Re
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*