- 您現在的位置：買賣IC網 > PDF目錄10753 > MCP3901A0T-I/SS (Microchip Technology)IC AFE 24BIT 64KSPS 20-SSOP PDF資料下載
參數資料
| 型號： | MCP3901A0T-I/SS |
| 廠商： | Microchip Technology |
| 文件頁數： | 18/30頁 |
| 文件大小： | 0K |
| 描述： | IC AFE 24BIT 64KSPS 20-SSOP |
| 產品培訓模塊： | MCP3901 Analog Front End |
| 標準包裝： | 1,600 |
| 位數： | 24 |
| 通道數： | 2 |
| 電壓 - 電源，模擬： | 4.5 V ~ 5.5 V |
| 電壓 - 電源，數字： | 2.7 V ~ 5.5 V |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
PCA2002
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 25 November 2011
25 of 30
NXP Semiconductors
PCA2002
32 kHz watch circuit with programmable output period and pulse width
14.3.2 Quality of solder joint
A flip-chip joint is considered to be a good joint when the entire solder land has been
wetted by the solder from the bump. The surface of the joint should be smooth and the
shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps
after reflow can occur during the reflow process in bumps with high ratio of bump diameter
to bump height, i.e. low bumps with large diameter. No failures have been found to be
related to these voids. Solder joint inspection after reflow can be done with X-ray to
monitor defects such as bridging, open circuits and voids.
14.3.3 Rework
In general, rework is not recommended. By rework we mean the process of removing the
chip from the substrate and replacing it with a new chip. If a chip is removed from the
substrate, most solder balls of the chip will be damaged. In that case it is recommended
not to re-use the chip again.
Device removal can be done when the substrate is heated until it is certain that all solder
joints are molten. The chip can then be carefully removed from the substrate without
damaging the tracks and solder lands on the substrate. Removing the device must be
done using plastic tweezers, because metal tweezers can damage the silicon. The
surface of the substrate should be carefully cleaned and all solder and flux residues
and/or underfill removed. When a new chip is placed on the substrate, use the flux
process instead of solder on the solder lands. Apply flux on the bumps at the chip side as
well as on the solder pads on the substrate. Place and align the new chip while viewing
with a microscope. To reflow the solder, use the solder profile shown in application note
AN10365 “Surface mount reflow soldering description”.
14.3.4 Cleaning
Cleaning can be done after reflow soldering.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX19706ETM+ | IC ANLG FRNT END 48-TQFN |
| MCP3911A0T-E/SS | IC AFE 24BIT 125KSPS 2CH 20-SSOP |
| MAX19710ETN+ | IC ANLG FRONT END 7.5MSPS 56TQFN |
| V300C2M50BG2 | CONVERTER MOD DC/DC 2V 50W |
| MAX19713ETN+ | IC ANLG FRONT END 45MSPS 56-TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3901A1-I/ML | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two Channel Analog Front End |
| MCP3901A1-I/SS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two Channel Analog Front End |
| MCP3901A1T-I/ML | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two Channel Analog Front End |
| MCP3901A1T-I/SS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two Channel Analog Front End |
| MCP3901A2-I/ML | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two Channel Analog Front End |
發布緊急采購，3分鐘左右您將得到回復。