- 您現在的位置：買賣IC網 > PDF目錄17041 > MCP3425EV (Microchip Technology)EVALUATION BOARD FOR MCP3425 PDF資料下載
參數資料
| 型號： | MCP3425EV |
| 廠商： | Microchip Technology |
| 文件頁數： | 11/38頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVALUATION BOARD FOR MCP3425 |
| 產品培訓模塊： | MCP3901 Analog Front End |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 15 ~ 240 |
| 數據接口： | I²C |
| 輸入范圍： | ±2.048 V |
| 工作溫度： | -40°C ~ 125°C |
| 已用 IC / 零件： | MCP3425 |
| 已供物品： | 板 |
| 產品目錄頁面： | 672 (CN2011-ZH PDF) |
| 相關產品： | MCP3425A0T-E/CHDKR-ND - IC ADC 16BIT I2C PROGBL SOT23-6 MCP3425A0T-E/CHCT-ND - IC ADC 16BIT I2C PROGBL SOT23-6 MCP3425A0T-E/CHTR-ND - IC ADC 16BIT I2C PROGBL SOT23-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
2009 Microchip Technology Inc.
DS22072B-page 19
MCP3425
5.4
General Call
The device acknowledges the general call address
(0x00 in the first byte). The meaning of the general call
address is always specified in the second byte. Refer
to Figure 5-4. The device supports the following two
general calls.
For more information on the general call, or other I2C
modes, please refer to the Phillips I2C specification.
5.4.1
GENERAL CALL RESET
The general call reset occurs if the second byte is
‘00000110’
(06h). At the acknowledgement of this
byte, the device will abort current conversion and
perform an internal reset similar to a Power-On-Reset
(POR). All configuration and data register bits are reset
to default values.
5.4.2
GENERAL CALL CONVERSION
The general call conversion occurs if the second byte
is ‘00001000’ (08h). All devices on the bus initiate a
conversion simultaneously. When the device receives
this command, the configuration will be set to the One-
Shot Conversion mode and a single conversion will be
performed. The PGA and data rate settings are
unchanged with this general call.
FIGURE 5-4:
General Call Address
Format.
5.5
High-Speed (HS) Mode
The I2C specification requires that a high-speed mode
device must be ‘a(chǎn)ctivated’ to operate in high-speed
mode. This is done by sending a special address byte
of “00001XXX” following the START bit. The “XXX” bits
are unique to the High-Speed (HS) mode Master. This
byte is referred to as the High-Speed (HS) Master
Mode Code (HSMMC). The MCP3425 device does not
acknowledge this byte. However, upon receiving this
code, the device switches on its HS mode filters and
communicates up to 3.4 MHz on SDA and SCL bus
lines. The device will switch out of the HS mode on the
next STOP condition.
For more information on the HS mode, or other I2C
modes, please refer to the Phillips I2C specification.
5.6
I2C Bus Characteristics
The I2C specification defines the following bus
protocol:
Data transfer may be initiated only when the bus
is not busy
During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH will be
interpreted as a START or STOP condition
Accordingly, the following bus conditions have been
defined using Figure 5-5.
5.6.1
BUS NOT BUSY (A)
Both data and clock lines remain HIGH.
5.6.2
START DATA TRANSFER (B)
A HIGH to LOW transition of the SDA line while the
clock (SCL) is HIGH determines a START condition. All
commands must be preceded by a START condition.
5.6.3
STOP DATA TRANSFER (C)
A LOW to HIGH transition of the SDA line while the
clock (SCL) is HIGH determines a STOP condition. All
operations can be ended with a STOP condition.
5.6.4
DATA VALID (D)
The state of the data line represents valid data when,
after a START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a START condition
and terminated with a STOP condition.
LSB
First Byte
ACK
X
0
0 A
A
XX X X XX X
(General Call Address)
Second Byte
Note:
The I2C specification does not allow
“00000000” (00h) in the second byte.
S
START
ACK
STOP
相關PDF資料 |
PDF描述 |
|---|---|
| ECE-A1EKG6R8 | CAP ALUM 6.8UF 25V 20% RADIAL |
| EEC22DREN-S93 | CONN EDGECARD 44POS .100 EYELET |
| MCP3424EV | EVALUATION BOARD FOR MCP3424 |
| EVAL-AD7946SDZ | BOARD EVAL FOR AD7946 |
| EEC22DREH-S93 | CONN EDGECARD 44POS .100 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3426 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3426A0-E/MC | 功能描述:模數轉換器 - ADC 16-bit delta-sigma ADC dual chan 15sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3426A0-E/MS | 功能描述:模數轉換器 - ADC 16-bit delta-sigma ADC dual chan 15sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3426A0-E/SN | 功能描述:模數轉換器 - ADC 16-bit delta-sigma ADC dual chan 15sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3426A0-E/SN | 制造商:Microchip Technology Inc 功能描述:A/D (A-D) CONVERTER IC |
發布緊急采購，3分鐘左右您將得到回復。