- 您現在的位置：買賣IC網 > PDF目錄17041 > MCP3423EV (Microchip Technology)BOARD EVAL 18BIT 2CH ADC MCP3423 PDF資料下載
參數資料
| 型號： | MCP3423EV |
| 廠商： | Microchip Technology |
| 文件頁數： | 5/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL 18BIT 2CH ADC MCP3423 |
| 產品培訓模塊： | MCP3901 Analog Front End |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 18 |
| 采樣率（每秒）： | 3.75 |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF |
| 工作溫度： | -40°C ~ 125°C |
| 已用 IC / 零件： | MCP3423 |
| 已供物品： | 板 |
| 產品目錄頁面： | 672 (CN2011-ZH PDF) |
| 相關產品： | MCP3423T-E/UNTR-ND - IC ADC 18BIT 3.75SPS 2CH 10-MSOP MCP3423T-E/MFTR-ND - IC ADC 18BIT 3.75SPS 2CH 10-DFN MCP3423-E/UN-ND - IC ADC 18BIT 3.75SPS 2CH 10-MSOP MCP3423-E/MF-ND - IC ADC 18BIT 3.75SPS 2CH 10-DFN |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
2009 Microchip Technology Inc.
DS22088C-page 13
MCP3422/3/4
4.0
DESCRIPTION OF DEVICE
OPERATION
4.1
General Overview
The MCP3422/3/4 devices are differential multi-
channel low-power, 18-Bit Delta-Sigma A/D converters
with an I2C serial interface. The devices contain an
input
channel
selection
multiplexer
(mux),
a
programmable gain amplifier (PGA), an on-board
voltage reference (2.048V), and an internal oscillator.
When the device powers up (POR is set), it
automatically resets the configuration bits to default
settings.
Device default settings are:
Conversion bit resolution: 12 bits (240 sps)
Input channel: Channel 1
PGA gain setting: x1
Continuous conversion
Once the device is powered-up, the user can
reprogram the configuration bits using I2C serial
interface any time. The configuration bits are stored in
volatile memory.
User selectable options are:
Conversion bit resolution: 12, 14, 16, or 18 bits
Input channel selection: CH1, CH2, CH3, or CH4.
PGA Gain selection: x1, x2, x4, or x8
Continuous or one-shot conversion
In the Continuous Conversion mode, the device
converts the inputs continuously. While in the One-Shot
Conversion mode, the device converts the input one
time and stays in the low-power standby mode until it
receives another command for a new conversion.
During the standby mode, the device consumes less
than 1 A maximum.
4.2
Power-On-Reset (POR)
The device contains an internal Power-On-Reset
(POR) circuit that monitors power supply voltage (VDD)
during operation. This circuit ensures correct device
start-up at system power-up and power-down events.
The device resets all configuration register bits to
default settings as soon as the POR is set.
The POR has built-in hysteresis and a timer to give a
high degree of immunity to potential ripples and noises
on the power supply. A 0.1 F decoupling capacitor
should be mounted as close as possible to the VDD pin
for additional transient immunity.
The threshold voltage is set at 2.2V with a tolerance of
approximately ±5%. If the supply voltage falls below
this threshold, the device will be held in a reset
condition. The typical hysteresis value is approximately
200 mV.
The POR circuit is shut-down during the low-power
standby mode. Once a power-up event has occurred,
the
device
requires
additional
delay
time
(approximately 300 s) before a conversion takes
place. During this time, all internal analog circuitries are
settled before the first conversion occurs. Figure 4-1
illustrates the conditions for power-up and power-down
events under typical start-up conditions.
FIGURE 4-1:
POR Operation.
4.3
Internal Voltage Reference
The device contains an on-board 2.048V voltage
reference. This reference voltage is for internal use
only and not directly measurable. The specification of
the reference voltage is part of the device’s gain and
drift specifications. Therefore, there is no separate
specification for the on-board reference.
4.4
Analog Input Channels
The user can select the input channel using the
configuration register bits. Each channel can be used
for differential or single-ended input.
Each input channel has a switched capacitor input
structure. The internal sampling capacitor (3.2 pF for
PGA = 1) is charged and discharged to process a
conversion. The charging and discharging of the input
sampling capacitor creates dynamic input currents at
each input pin. The current is a function of the
differential input voltages, and inversely proportional to
the internal sampling capacitance, sampling frequency,
and PGA setting.
VDD
2.2V
2.0V
300 S
Reset Start-up
Normal Operation
Reset
Time
相關PDF資料 |
PDF描述 |
|---|---|
| CDB5571 | DEV BOARD FOR CS5571 W/MUX |
| UPB2C821MRD | CAP ALUM 820UF 160V 20% RADIAL |
| LLS2D561MELZ | CAP ALUM 560UF 200V 20% SNAP |
| EEC22DRTH-S93 | CONN EDGECARD 44POS DIP .100 SLD |
| MCP3425EV | EVALUATION BOARD FOR MCP3425 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3423T-E/MC | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3423T-E/MF | 功能描述:模數轉換器 - ADC 18B delta-sigma ADC dual Ch 4sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3423T-E/MS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3423T-E/SL | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3423T-E/SN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
發布緊急采購，3分鐘左右您將得到回復。