- 您現在的位置：買賣IC網 > PDF目錄1953 > MCP2200-I/MQ (Microchip Technology)IC USB TO UART 20QFN PDF資料下載
參數資料
| 型號： | MCP2200-I/MQ |
| 廠商： | Microchip Technology |
| 文件頁數： | 43/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC USB TO UART 20QFN |
| 特色產品： | MCP2200 USB-to-UART Serial Converter |
| 標準包裝： | 73 |
| 特點： | USB 至 UART |
| 通道數： | 8 |
| FIFO's： | 256 字節 |
| 規程： | USB 2.0 |
| 電源電壓： | 3 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VQFN 裸露焊盤 |
| 供應商設備封裝： | 20-VQFN |
| 包裝： | 管件 |
| 產品目錄頁面： | 684 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁
MCP2200
DS22228B-page 8
2011 Microchip Technology Inc.
1.6.1.3
RxLED Pin Function (IN Message)
The ‘Rx’ in the pin name is in respect to the USB host.
The RxLED pin is an indicator for USB ‘IN’ messages.
This pin will either pulse low for a period of time
(configurable for ~100 ms or ~200 ms), or toggle to the
opposite
state
for
every
message
received
(IN message) by the USB host. This allows the
application to count messages or provide a visual
indication of USB traffic.
1.6.1.4
TxLED Pin Function (OUT Message)
The ‘Tx’ in the pin name is in respect to the USB host.
The TxLED pin is an indicator for USB ‘OUT’
messages.
This pin will either pulse low for a period of time
(configurable for ~100 ms or ~200 ms), or toggle to the
opposite state for every message transmitted (OUT
message) by the USB host. This allows the application
to count messages or provide a visual indication of
USB traffic.
1.7
EEPROM Module
The EEPROM module is a 256 byte array of nonvolatile
memory. The memory locations are accessed for
read/write operations via USB host commands. Refer
to Section 2.0 “Configuration” for details on access-
ing the EEPROM. The memory cells for data EEPROM
are rated to endure thousands of erase/write cycles,
up to 100K for EEPROM.
Data retention without refresh is conservatively
estimated to be greater than 40 years.
The host should wait for the write cycle to complete and
then verify the write by reading the byte(s).
1.8
RESET/POR
1.8.1
RESET PIN
The RST pin provides a method for triggering an
external Reset of the device. A Reset is generated by
holding the pin low. These devices have a noise filter in
the Reset path which detects and ignores small pulses.
1.8.2
POR
A POR pulse is generated on-chip whenever VDD rises
above a certain threshold. This allows the device to
start in the initialized state when VDD is adequate for
operation.
To take advantage of the POR circuitry, tie the RST pin
through a resistor (1 kOhm to 10 kOhm) to VDD. This
will eliminate external RC components usually needed
to create a POR delay.
When the device starts normal operation (i.e., exits the
Reset
condition),
device
operating
parameters
(voltage, frequency, temperature, etc.) must be met to
ensure operation. If these conditions are not achieved,
the device must be held in Reset until the operating
conditions are met.
1.9
Oscillator
The input clock must be 12 MHz to provide the proper
frequency for the USB module.
USB full-speed is nominally 12 Mb/s. The clock input
accuracy is ±0.25% (2,500 ppm maximum).
FIGURE 1-6:
QUARTZ CRYSTAL
OPERATION
FIGURE 1-7:
CERAMIC RESONATOR
OPERATION
Quartz Crystal
12 MHz
OSC1
OSC2
RS(1)
RF(2)
MCP2200
Note 1:
A series resistor (RS) may be required
for quartz crystals with high drive level.
2:
The value of RF is typically between
2M
to 10 M..
Example: muRata
CSTCE12M0G15L
OSC1
OSC2
Resonator
12 MHz
MCP2200
相關PDF資料 |
PDF描述 |
|---|---|
| MCP2200T-I/MQ | IC USB 2.0 - UART 20QFN |
| MCP2210T-I/MQ | IC CONVERTER USB-PCI 20-QFN |
| MCP23008-E/ML | IC I/O EXPANDER I2C 8B 20QFN |
| MCP23016T-I/ML | IC I/O EXPANDER I2C 16B 28QFN |
| MCP23018T-E/SS | IC I/O EXPANDER I2C 16B 24SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2200-ISO | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:USB 2.0 to UART Protocol Converter with GPIO |
| MCP2200-ISS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:USB 2.0 to UART Protocol Converter with GPIO |
| MCP2200T-I/MQ | 功能描述:USB 接口集成電路 USB-to-UART Protocol Converter w/ GPIO RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MCP2200T-I/NQ | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:USB 2.0 to UART Protocol Converter with GPIO |
| MCP2200T-I/SO | 功能描述:USB 接口集成電路 USB-to-UART Protocol Converter w/ GPIO RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。