- 您現在的位置：買賣IC網 > PDF目錄382311 > MC74LVX4066D (ON SEMICONDUCTOR) Quad Analog Switch/Multiplexer/Demultiplexer PDF資料下載
參數資料
| 型號： | MC74LVX4066D |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 運動控制電子 |
| 英文描述： | Quad Analog Switch/Multiplexer/Demultiplexer |
| 中文描述： | QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO14 |
| 封裝： | SOIC-14 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 271K |
| 代理商： | MC74LVX4066D |
MC74LVX4066
http://onsemi.com
8
0
–10
–20
–30
–40
–50
1.0
2.0
FREQUENCY (kHz)
d
–60
–70
–80
–90
FUNDAMENTAL FREQUENCY
DEVICE
SOURCE
Figure 15. Plot, Harmonic Distortion
3.0
APPLICATION INFORMATION
The ON/OFF Control pins should be at VCC or GND logic
levels, VCC being recognized as logic high and GND being
recognized as a logic low. Unused analog inputs/outputs
may be left floating (not connected). However, it is
advisable to tie unused analog inputs and outputs to VCC or
GND through a low value resistor. This minimizes crosstalk
and feedthrough noise that may be picked–up by the unused
I/O pins.
The maximum analog voltage swings are determined by
the supply voltages VCC and GND. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below GND. In the example
below, the difference between VCC and GND is six volts.
Therefore, using the configuration in Figure 16, a maximum
analog signal of six volts peak–to–peak can be controlled.
When voltage transients above VCC and/or below GND
are anticipated on the analog channels, external diodes (Dx)
are recommended as shown in Figure 17. These diodes
should be small signal, fast turn–on types able to absorb the
maximum anticipated current surges during clipping. An
alternate method would be to replace the Dx diodes with
Mosorbs (Mosorb
is an acronym for high current surge
protectors). Mosorbs are fast turn–on devices ideally suited
for precise DC protection with no inherent wear out
mechanism.
ANALOG O/I
ON
14
VCC = 6.0 V
ANALOG I/O
+ 6.0 V
0 V
+ 6.0 V
0 V
OTHER CONTROL
INPUTS
(VCC OR GND)
ON
16
VCC
Dx
Dx
VCC
Dx
Figure 16. 6.0 V Application
Figure 17. Transient Suppressor Application
7
SELECTED
CONTROL
INPUT
Dx
OTHER CONTROL
INPUTS
(VCC OR GND)
7
SELECTED
CONTROL
INPUT
VCC
相關PDF資料 |
PDF描述 |
|---|---|
| MC74LVX4066DR2 | Quad Analog Switch/Multiplexer/Demultiplexer |
| MC74LVX4066DT | Quad Analog Switch/Multiplexer/Demultiplexer |
| MC74LVX4066DTR2 | Quad Analog Switch/Multiplexer/Demultiplexer |
| MC74LVX8051 | Analog Multiplexer/Demultiplexer |
| MC74LVX8051D | Analog Multiplexer/Demultiplexer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC74LVX4066DR2 | 功能描述:多路器開關 IC 2-6V Quad Mux/Demux RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC74LVX4066DR2G | 功能描述:多路器開關 IC 2-6V Quad Mux/Demux -55 to 85deg C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC74LVX4066DT | 制造商:ON Semiconductor 功能描述:Analog Switch Quad SPST 14-Pin TSSOP Rail |
| MC74LVX4066DTR2 | 功能描述:多路器開關 IC 2-6V Quad Mux/Demux RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC74LVX4066DTR2G | 功能描述:多路器開關 IC 2-6V Quad Mux/Demux -55 to 85deg C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。