- 您現在的位置：買賣IC網 > PDF目錄382310 > MC74HC4538AN (ON SEMICONDUCTOR) Dual Precision Monostable Multivibrator(Retriggerable, Resettable) PDF資料下載
參數資料
| 型號： | MC74HC4538AN |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 諧振器 |
| 英文描述： | Dual Precision Monostable Multivibrator(Retriggerable, Resettable) |
| 中文描述： | HC/UH SERIES, DUAL MONOSTABLE MULTIVIBRATOR, PDIP16 |
| 封裝： | PLASTIC, DIP-16 |
| 文件頁數： | 9/16頁 |
| 文件大小： | 159K |
| 代理商： | MC74HC4538AN |
MC74HC4538A
http://onsemi.com
9
PIN DESCRIPTIONS
INPUTS
A1, A2 (Pins 4, 12)
Positive–edge trigger inputs. A rising–edge signal on
either of these pins triggers the corresponding multivibrator
when there is a high level on the B1 or B2 input.
B1, B2 (Pins 5, 11)
Negative–edge trigger inputs. A falling–edge signal on
either of these pins triggers the corresponding multivibrator
when there is a low level on the A1 or A2 input.
Reset 1, Reset 2 (Pins 3, 13)
Reset inputs (active low). When a low level is applied to
one of these pins, the Q output of the corresponding
multivibrator is reset to a low level and the Q output is set to
a high level.
C
X
1/R
X
1 and C
X
2/R
X
2 (Pins 2 and 14)
External timing components. These pins are tied to the
common points of the external timing resistors and
capacitors (see the Block Diagram). Polystyrene capacitors
are recommended for optimum pulse width control.
Electrolytic capacitors are not recommended due to high
leakages associated with these type capacitors.
GND (Pins 1 and 15)
External ground. The external timing capacitors discharge
to ground through these pins.
OUTPUTS
Q1, Q2 (Pins 6, 10)
Noninverted monostable outputs. These pins (normally
low) pulse high when the multivibrator is triggered at either
the A or the B input. The width of the pulse is determined by
the external timing components, R
X
and C
X
.
Q1, Q2 (Pins 7, 9)
Inverted monostable outputs. These pins (normally high)
pulse low when the multivibrator is triggered at either the A
or the B input. These outputs are the inverse of Q1 and Q2.
+
UPPER
–
+
–
RxCx
V
CC
M1
2 k
M3
M2
A
B
RESET
POWER
ON
RESET
RESET LATCH
TRIGGER CONTROL
RESET CIRCUIT
TRIGGER
CONTROL CIRCUIT
OUTPUT
LATCH
UPPER
REFERENCE
CIRCUIT
V
re
,
LOWER
REFERENCE
CIRCUIT
V
re
,
LOWER
Q
Q
C
CB
Q
R
V
CC
Figure 11. Logic Detail (1/2 the Device)
相關PDF資料 |
PDF描述 |
|---|---|
| MC74HC573A | Octal 3-State Noninverting Transparent Latch |
| MC74HC573ADT | Octal 3-State Noninverting Transparent Latch |
| MC74HC573ADTR2 | Octal 3-State Noninverting Transparent Latch |
| MC74HC573ADW | Octal 3-State Noninverting Transparent Latch |
| MC74HC573ADWR2 | Octal 3-State Noninverting Transparent Latch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC74HC4538ANG | 功能描述:單穩態多諧振蕩器 3-6V Dual Precision MonoStable RoHS:否 制造商:Texas Instruments 每芯片元件:1 邏輯系列:LVC 邏輯類型:Monostable Multivibrator 封裝 / 箱體:SSOP-8 傳播延遲時間:18.6 ns 高電平輸出電流:- 32 mA 低電平輸出電流:32 mA 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MC74HC4851AD | 功能描述:多路器開關 IC Mux/Demux Injection RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC74HC4851ADG | 功能描述:多路器開關 IC Mux/Demux Injection Current Effect CNTRL RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC74HC4851ADR2 | 功能描述:多路器開關 IC Mux/Demux Injection RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC74HC4851ADR2G | 功能描述:多路器開關 IC Mux/Demux Injection Current Effect CNTRL RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。