- 您現在的位置：買賣IC網 > PDF目錄382310 > MC74HC4538AD (ON SEMICONDUCTOR) Dual Precision Monostable Multivibrator(Retriggerable, Resettable) PDF資料下載
參數資料
| 型號： | MC74HC4538AD |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 諧振器 |
| 英文描述： | Dual Precision Monostable Multivibrator(Retriggerable, Resettable) |
| 中文描述： | HC/UH SERIES, DUAL MONOSTABLE MULTIVIBRATOR, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 159K |
| 代理商： | MC74HC4538AD |
MC74HC4538A
http://onsemi.com
11
When C
x
charges up to the reference voltage of the upper
reference circuit (#17), the output of the upper reference
circuit goes low (#18). This causes the output latch to toggle,
taking the Q output of the HC4538A to a low state (#19), and
completing the time–out cycle.
POWER–DOWN CONSIDERATIONS
Large values of C
x
may cause problems when powering
down the HC4538A because of the amount of energy stored
in the capacitor. When a system containing this device is
powered down, the capacitor may discharge from V
CC
through the input protection diodes at pin 2 or pin 14.
Current through the protection diodes must be limited to 30
mA; therefore, the turn–off time of the V
CC
power supply
must not be faster than t = V
CC
C
x
/(30 mA). For example,
if V
CC
= 5.0 V and C
x
= 15
μ
F, the V
CC
supply must turn off
no faster than t = (5.0 V) (15
μ
F)/30 mA = 2.5 ms. This is
usually not a problem because power supplies are heavily
filtered and cannot discharge at this rate.
When a more rapid decrease of V
CC
to zero volts occurs,
the HC4538A may sustain damage. To avoid this possibility,
use an external damping diode, D
x
, connected as shown in
Figure 11. Best results can be achieved if diode D
x
is chosen
to be a germanium or Schottky type diode able to withstand
large current surges.
RESET AND POWER ON RESET OPERATION
A low voltage applied to the Reset pin always forces the
Q output of the HC4538A to a low state.
The timing diagram illustrates the case in which reset
occurs (#20) while C
x
is charging up toward the reference
voltage of the upper reference circuit (#21). When a reset
occurs, the output of the reset latch goes low (#22), turning
on transistor M1. Thus C
x
is allowed to quickly charge up to
V
CC
(#23) to await the next trigger signal.
On power up of the HC4538A the power–on reset circuit
will be high causing a reset condition. This will prevent the
trigger–control circuit from accepting a trigger input during
this state. The HC4538A’s Q outputs are low and the Q not
outputs are high.
RETRIGGER OPERATION
When used in the retriggerable mode (Figure 12), the
HC4538A may be retriggered during timing out of the
output pulse at any time after the trigger–control circuit
flip–flop has been reset (#24), and the voltage across C
x
is
above the lower reference voltage. As long as the C
x
voltage
is below the lower reference voltage, the reset of the
flip–flop is high, disabling any trigger pulse. This prevents
M3 from turning on during this period resulting in an output
pulse width that is predictable.
The amount of undershoot voltage on R
x
C
x
during the
trigger mode is a function of loop delay, M3 conductivity,
and V
DD
. Minimum retrigger time, trr (Figure 7), is a
function of 1) time to discharge R
x
C
x
from V
DD
to lower
reference voltage (T
discharge
); 2) loop delay (T
delay
); 3)
time to charge R
x
C
x
from the undershoot voltage back to the
lower reference voltage (T
charge
).
Figure 13 shows the device configured in the
non–retriggerable mode.
For additional information, please see Application Note
(AN1558/D) titled
Characterization of Retrigger Time in
the HC4538A Dual Precision Monostable Multivibrator
.
D
X
C
X
V
CC
Q
Q
RESET
A
B
Figure 13. Discharge Protection During Power Down
R
X
相關PDF資料 |
PDF描述 |
|---|---|
| MC74HC4538ADR2 | Dual Precision Monostable Multivibrator(Retriggerable, Resettable) |
| MC74HC4538AN | Dual Precision Monostable Multivibrator(Retriggerable, Resettable) |
| MC74HC573A | Octal 3-State Noninverting Transparent Latch |
| MC74HC573ADT | Octal 3-State Noninverting Transparent Latch |
| MC74HC573ADTR2 | Octal 3-State Noninverting Transparent Latch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC74HC4538ADG | 功能描述:單穩態多諧振蕩器 3-6V Dual Precision MonoStable RoHS:否 制造商:Texas Instruments 每芯片元件:1 邏輯系列:LVC 邏輯類型:Monostable Multivibrator 封裝 / 箱體:SSOP-8 傳播延遲時間:18.6 ns 高電平輸出電流:- 32 mA 低電平輸出電流:32 mA 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MC74HC4538ADG | 制造商:ON Semiconductor 功能描述:MULTIVIBRATOR LOGIC IC |
| MC74HC4538ADR2 | 功能描述:單穩態多諧振蕩器 3-6V Dual Precision RoHS:否 制造商:Texas Instruments 每芯片元件:1 邏輯系列:LVC 邏輯類型:Monostable Multivibrator 封裝 / 箱體:SSOP-8 傳播延遲時間:18.6 ns 高電平輸出電流:- 32 mA 低電平輸出電流:32 mA 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MC74HC4538ADR2G | 功能描述:單穩態多諧振蕩器 3-6V Dual Precision MonoStable RoHS:否 制造商:Texas Instruments 每芯片元件:1 邏輯系列:LVC 邏輯類型:Monostable Multivibrator 封裝 / 箱體:SSOP-8 傳播延遲時間:18.6 ns 高電平輸出電流:- 32 mA 低電平輸出電流:32 mA 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MC74HC4538ADR2G-CUT TAPE | 制造商:ON 功能描述:MC74HC4538A Series 3 to 6 V Dual Precision Monostable Multivibrator - SOIC-16 |
發布緊急采購，3分鐘左右您將得到回復。