參數資料
型號： MC68L11D0FNE2
廠商： Freescale Semiconductor
文件頁數： 83/124頁
文件大?。?/td> 0K
描述： IC MCU 8BIT 192RAM 44-PLCC
標準包裝： 26
系列： HC11
核心處理器： HC11
芯體尺寸： 8-位
速度： 2MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 26
程序存儲器類型： ROMless
RAM 容量： 192 x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 5.5 V
振蕩器型： 內部
工作溫度： 0°C ~ 70°C
封裝/外殼： 44-LCC（J 形引線）
包裝： 管件
RESETS AND INTERRUPTS
TECHNICAL DATA
5-17
nals driving on-chip peripheral functions can be shut down. The CPU is always shut
down during WAIT. While in the wait state, the address/data bus repeatedly runs read
cycles to the address where the CCR contents were stacked. The MPU leaves the wait
state when it senses any interrupt that has not been masked.
The free-running timer system is shut down only if the I bit is set to one and the COP
system is disabled by NOCOP being set to one. Several other systems can also be in
a reduced power consumption state depending on the state of software-controlled
configuration control bits. The SPI system is enabled or disabled by the SPE control
bit. The SCI transmitter is enabled or disabled by the TE bit, and the SCI receiver is
enabled or disabled by the RE bit. Therefore the power consumption in WAIT is de-
pendent on the particular application.
5.5.2 STOP
Executing the STOP instruction while the S bit in the CCR is equal to zero places the
MCU in the STOP condition. If the S bit is not zero, the STOP opcode is treated as a
no-op (NOP). The STOP condition offers minimum power consumption because all
clocks, including the crystal oscillator, are stopped while in this mode. To exit STOP
and resume normal processing, a logic low level must be applied to one of the external
interrupts (IRQ or XIRQ), or to the RESET pin. A pending edge-triggered IRQ can also
bring the CPU out of STOP.
Because all clocks are stopped in this mode, all internal peripheral functions also stop.
The data in the internal RAM is retained as long as VDD power is maintained. The CPU
state and I/O pin levels are static and are unchanged by STOP. Therefore, when an
interrupt comes to restart the system, the MCU resumes processing as if there were
no interruption. If reset is used to restart the system a normal reset sequence results
where all I/O pins and functions are also restored to their initial states.
To use the IRQ pin as a means of recovering from STOP, the I bit in the CCR must be
clear (IRQ not masked). The XIRQ pin can be used to wake up the MCU from STOP
regardless of the state of the X bit in the CCR, although the recovery sequence de-
pends on the state of the X bit. If X is set to zero (XIRQ not masked), the MCU starts
up, beginning with the stacking sequence leading to normal service of the XIRQ re-
quest. If X is set to one (XIRQ masked or inhibited), then processing continues with
the instruction that immediately follows the STOP instruction, and no XIRQ interrupt
service is requested or pending.
Because the oscillator is stopped in STOP mode, a restart delay may be imposed to
allow oscillator stabilization upon leaving STOP. If the internal oscillator is being used,
this delay is required; however, if a stable external oscillator is being used, the DLY
control bit can be used to bypass this startup delay. The DLY control bit is set by reset
and can be optionally cleared during initialization. If the DLY equal to zero option is
used to avoid startup delay on recovery from STOP, then reset should not be used as
the means of recovering from STOP, as this causes DLY to be set again by reset, im-
posing the restart delay. This same delay also applies to power-on-reset, regardless
of the state of the DLY control bit, but does not apply to a reset while the clocks are
running.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
VE-B14-CU-F2 CONVERTER MOD DC/DC 48V 200W
MC68L11D0CFBE2 IC MCU 8BIT LV 192RAM 44-QFP
VE-B14-CU-F1 CONVERTER MOD DC/DC 48V 200W
VI-B1K-CU-F2 CONVERTER MOD DC/DC 40V 200W
MC68HSR705J1ACPE IC MCU 8BIT 64 BYTES RAM 20-PDIP
相關代理商/技術參數
參數描述
MC68L11E0FN2 制造商:Rochester Electronics LLC 功能描述:8-BIT MCU,512RAM,A/D,LVDC - Bulk
MC68L11E0FNE2 功能描述:IC MCU 8BIT LV 512RAM 52-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:1 系列:87C 核心處理器:MCS 51 芯體尺寸:8-位 速度:16MHz 連通性:SIO 外圍設備:- 輸入/輸出數:32 程序存儲器容量:8KB（8K x 8） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 6 V 數據轉換器:- 振蕩器型:外部 工作溫度:0°C ~ 70°C 封裝/外殼:44-DIP 包裝:管件 其它名稱:864285
MC68L11E1CFNE2 功能描述:8位微控制器 -MCU 8B MCU RAM EE A/D LVDC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L11E1FNE2 功能描述:8位微控制器 -MCU 8B MCU RAM EE A/D LVD RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L11F1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512BYTES RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*