- 您現在的位置：買賣IC網 > PDF目錄371048 > MC68HC11A1CFN2 (MOTOROLA INC) HCMOS Single-Chip Microcontroller PDF資料下載
參數資料
| 型號： | MC68HC11A1CFN2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HCMOS Single-Chip Microcontroller |
| 中文描述： | 8-BIT, 2 MHz, MICROCONTROLLER, PQCC52 |
| 封裝： | PLASTIC, LCC-52 |
| 文件頁數： | 17/158頁 |
| 文件大?。?/td> | 776K |
| 代理商： | MC68HC11A1CFN2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
MC68HC11A8
TECHNICAL DATA
SIGNAL DESCRIPTIONS AND OPERATING MODES
MOTOROLA
2-1
2
2 SIGNAL DESCRIPTIONS AND OPERATING MODES
The signal descriptions and operating modes are presented in this section. When the
microcontroller is in an expanded multiplexed operating mode, 18 pins change func-
tion to support a multiplexed address/data bus.
2.1 Signal Pin Descriptions
The following paragraphs provide a description of the input/output signals. Reference
is made, where applicable, to other sections that contain more detail about the function
being performed.
2.1.1 Input Power (V
Power is supplied to the microcontroller using these pins. V
put and V
SS
is ground. Although the MC68HC11A8 is a CMOS device, very fast signal
transitions are present on many of its pins. Short rise and fall times are present even
when the microcontroller is operating at slow clock rates. Special care must be taken
to provide good power supply bypassing at the MCU. Recommended bypassing would
include a 0.1
μ
F ceramic capacitor between the V
cent to one of the two pins. A bulk capacitance, whose size depends on the other cir-
cuitry in the system, should also be present on the circuit board.
DD
) and Ground (V
SS
)
DD
is the positive power in-
DD
and V
SS
pins and physically adja-
2.1.2 Reset (RESET)
This active low bidirectional control signal is used as an input to initialize the
MC68HC11A8 to a known start-up state, and as an open-drain output to indicate that
an internal failure has been detected in either the clock monitor or computer operating
properly (COP) watchdog circuit. This reset signal is significantly different from the re-
set signal used on other Motorola MCUs. Please refer to
AND LOW POWER MODES
before designing circuitry to generate or monitor this sig-
nal.
9 RESETS, INTERRUPTS,
2.1.3 Crystal Driver and External Clock Input (XTAL, EXTAL)
These two pins provide the interface for either a crystal or a CMOS compatible clock
to control the internal clock generator circuitry. The frequency applied to these pins
shall be four times higher than the desired E clock rate. The XTAL pin is normally left
unterminated when using an external CMOS compatible clock input to the EXTAL pin.
However, a 10K to 100K load resistor to ground may be used to reduce RFI noise
emission. The XTAL output is normally intended to drive only a crystal.
The XTAL output may be buffered with a high-input-impedance buffer such as the
74HC04, or it may be used to drive the EXTAL input of another M68HC11.
In all cases take extra care in the circuit board layout around the oscillator pins. Load
capacitances shown in the oscillator circuits include all stray layout capacitances. Re-
fer to
Figure 2-1
,
Figure 2-2
, and
Figure 2-3
for diagrams of oscillator circuits.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HCP11A1CFN2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CFN3 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CP2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CP3 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1MFN2 | HCMOS Single-Chip Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11A1CFN3 | 制造商:Rochester Electronics LLC 功能描述: |
| MC68HC11A1CFNE3 | 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC11A1CFNE3 | 制造商:Freescale Semiconductor 功能描述:8-BIT MICROCONTROLLER IC |
| MC68HC11A1CFNE3R | 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC11A1CFU2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。