參數資料
型號： MC68HC11A0FU3
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： ROM-based high-performance microcontrollers
中文描述： 基于ROM的高性能微控制器
文件頁數： 46/124頁
文件大?。?/td> 840K
代理商： MC68HC11A0FU3
RESETS AND INTERRUPTS
5-2
TECHNICAL DATA
COP is enabled, the software is responsible for keeping a free-running watchdog timer
from timing out. When the software is no longer being executed in the intended se-
quence, a system reset is initiated.
The state of the NOCOP bit in the CONFIG register determines whether the COP sys-
tem is enabled or disabled. In normal modes, COP is enabled out of reset and does
not depend on software action. To disable the COP system, set the NOCOP bit in the
CONFIG register. In the special test and bootstrap operating modes, the COP system
is initially inhibited by the disable resets (DISR) control bit in the TEST1 register. The
DISR bit can subsequently be written to zero to enable COP resets.
The COP timer rate control bits CR[1:0] in the OPTION register determine the COP
time-out period. The system E clock is divided by 2
15
and then further scaled by a fac-
tor shown in
Table 5-1
. After reset, these bits are zero, which selects the fastest time-
out period. In normal operating modes, these bits can only be written once within 64
bus cycles after reset.
Complete the following reset sequence to service the COP timer. Write $55 to CO-
PRST to arm the COP timer clearing mechanism. Then write $AA to COPRST to clear
the COP timer. Performing instructions between these two steps is possible as long as
both steps are completed in the correct sequence before the timer times out.
5.1.4 Clock Monitor Reset
The clock monitor circuit is based on an internal RC time delay. If no MCU clock edges
are detected within this RC time delay, the clock monitor can optionally generate a sys-
tem reset. The clock monitor function is enabled or disabled by the CME control bit in
the OPTION register. The presence of a time-out is determined by the RC delay, which
allows the clock monitor to operate without any MCU clocks.
Clock monitor is used as a backup for the COP system. Because the COP needs a
clock to function, it is disabled when the clocks stop. Therefore, the clock monitor sys-
tem can detect clock failures not detected by the COP system.
Table 5-1 COP Time-out
CR[1:0]
Divide
E/2
15
By
1
4
16
64
E =
XTAL = 4.0 MHz
Time-out
–0/+32.8 ms
XTAL = 8.0 MHz
Time-out
–0/+16.4 ms
XTAL = 12.0 MHz
Time-out
–0/+10.9 ms
0 0
0 1
1 0
1 1
32.768 ms
131.072 ms
524.288 ms
2.097 sec
1.0 MHz
16.384 ms
65.536 ms
262.140 ms
1.049 sec
2.0 MHz
10.923 ms
43.691 ms
174.76 ms
699.05 ms
3.0 MHz
COPRST
— Am/Reset COP Timer Circuitry
$003A
Bit 7
7
0
6
6
0
5
5
0
4
4
0
3
3
0
2
2
0
1
1
0
Bit 0
0
0
RESET:
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC68HC11A0FU4 ROM-based high-performance microcontrollers
MC68HC11A0MFB ROM-based high-performance microcontrollers
MC68HC11A0MFB1 ROM-based high-performance microcontrollers
MC68HC11A0MFB3 ROM-based high-performance microcontrollers
MC68HC11A0MFB4 ROM-based high-performance microcontrollers
相關代理商/技術參數
參數描述
MC68HC11A0FU4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11A0MFB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11A0MFB1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11A0MFB3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11A0MFB4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*