OPERATIONAL MODES EXAMPLE OF NORMAL MODE OPE" />
參數資料
型號： MC33975EK
廠商： Freescale Semiconductor
文件頁數： 14/32頁
文件大?。?/td> 0K
描述： IC SWITCH DETECT MULT 32-SOICW
標準包裝： 42
應用： 開關監控
接口： SPI 串行
封裝/外殼： 32-BSOP（0.295"，7.50mm 寬）裸露焊盤
供應商設備封裝： 32-SOICW 裸露焊盤
包裝： 管件
安裝類型： 表面貼裝
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
33975
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
EXAMPLE OF NORMAL MODE OPERATION
The operation of the device in Normal mode is defined by the
states of the programmable internal control registers. A
typical application may have the following settings:
Programmable switch – set to switch-to-ground
All inputs set as wake-up
Wetting current on (32 mA)
Wetting current timer on (20 ms)
All inputs tri-state-disabled (comparator is active)
Analog select 00000 (no input channel selected)
With the device programmed as above, an interrupt will be
generated with each switch contact change of state (open-to-
close or close-to-open) and 32 mA of contact wetting current
will be source for 20 ms. The INT pin will remain low until
switch status is acknowledged by the microprocessor. It is
critical to understand INT will not be cleared on the rising
edge of CS if a switch closure occurs while the CS is low. The
maximum duration a switch state change can exist without
acknowledgement depends on the software response time to
the interrupt. Figure 6, page 11, shows the interaction
between changing input states and the INT and CS pins.
If desired the user may disable interrupts (wake-up/interrupt
command) from the 33975 device and read the switch states
on a periodic basis. Switch activation and deactivation faster
than the MCU read rate will not be acknowledged.
The 33975 device will exit the Normal mode and enter the
Sleep mode only with a valid sleep command.
SLEEP MODE
Sleep mode is used to reduce system quiescent currents.
Sleep mode may be entered only by sending the sleep
command. All register settings programmed in Normal mode
will be maintained in Sleep mode.
The 33975 will exit Sleep mode and enter Normal mode when
any of the following events occur:
Input switch change of state (when enabled)
Interrupt timer expire
Falling edge of WAKE
Falling edge of INT (with VDD = 5.0 V and WAKE at
Logic [1])
Falling edge of CS (with VDD = 5.0 V)
Power-on reset (POR)
The VDD supply may be removed from the device during
Sleep mode. However removing VDD from the device in
Sleep mode will disable a wake-up from falling edge of INT
and CS.
Note: In cases where CS is used to wake the device, the first
SO data message is not valid.
The sleep command contains settings for two programmable
timers for Sleep mode, the interrupt timer and the scan timer,
as shown in Table 18.
Table 16. Serial Output (SO) Bit Data
Type of Input
Input
Programmed
Voltage on Input
Pin
SO SPI Bit
SP
Switch to Ground
SPn < 4.0 V
1
Switch to Ground
SPn > 4.0 V
0
Switch to Battery
SPn < 4.0 V
0
Switch to Battery
SPn > 4.0 V
1
SG
N/A
SGn < 4.0 V
1
N/A
SGn > 4.0 V
0
Table 17. Serial Output (SO) Response Register
SO Response
Will
Always Send
ther
m
flg
RST
flg
SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 SG1
3
SG1
2
SG1
1
SG1
0
SG9 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0
Table 18. Sleep Command
Sleep Command
Command Bits
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
0
X
int
timer
int
timer
int
timer
sca
ntimer
sca
ntimer
sca
ntimer
相關PDF資料
PDF描述
000-36875 CONN PLUG BNC STR CRIMP 50 OHM
VE-B7J-IW-F4 CONVERTER MOD DC/DC 36V 100W
VE-B7H-IX-F3 CONVERTER MOD DC/DC 52V 75W
VE-B7H-IW-F2 CONVERTER MOD DC/DC 52V 100W
ADUC834BCPZ IC MCU 62K FLASH ADC/DAC 56LFCSP
相關代理商/技術參數
參數描述
MC33975EKR2 功能描述:多路器開關 IC EMSDI RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MC33975TEK 功能描述:接口 - 專用 MULTI SW DETECT INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MC33975TEKR2 功能描述:接口 - 專用 MULTI SW DETECT INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MC33981ABHFK 功能描述:電源開關 IC - 配電 HF 4.0MOHM RDSON SWITCH RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MC33981ABHFKR2 功能描述:電源開關 IC - 配電 HF 4.0MOHM RDSON SWITCH RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*