OPERATIONAL MODES The interrupt timer is use" />
參數資料
型號： MC33975ATEKR2
廠商： Freescale Semiconductor
文件頁數： 15/32頁
文件大?。?/td> 0K
描述： IC SWITCH DETECT MULT 32-SOIC
標準包裝： 1,000
應用： 開關監控
接口： SPI 串行
封裝/外殼： 32-BSOP（0.295"，7.50mm 寬）裸露焊盤
供應商設備封裝： 32-SOICW 裸露焊盤
包裝： 帶卷 (TR)
安裝類型： 表面貼裝
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
33975
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
The interrupt timer is used as a periodic wake-up timer. When
the timer expires, an interrupt is generated and the device
enters Normal mode.
Note: The interrupt timer in the 33975 device may be
disabled by programming the interrupt bits to logic [1 1 1].
Table 19 shows the programmable settings of the Interrupt
timer.
The scan timer sets the polling period between input switch
reads in Sleep mode. The period is set in the sleep command
and may be set to 000 (no period) to 111 (64 ms). In Sleep
mode when the scan timer expires, inputs will behave as
programmed prior to sleep command. The 33975 will wake
up for approximately 125
s and read the switch inputs. At
the end of the 125
s, the input switch states are compared
with the switch state prior to sleep command. When switch
state changes are detected, an interrupt (when enabled; refer
to wake-up/interrupt command description on page 17) is
generated and the device enters Normal mode. Without
switch state changes, the 33975 will reset the scan timer,
inputs become tri-state, and the Sleep mode continues until
the scan timer expires again.
Table 20 shows the programmable settings of the Scan
timer.
Note: The interrupt and scan timers are disabled in the
Normal Mode.
Figure 5, page 11, is a graphical description of how the
33975 device exits Sleep mode and enters Normal mode.
Notice that the device will exit Sleep mode when the interrupt
timer expires or when a switch change of state occurs. The
falling edge of INT triggers the MCU to wake from Sleep state.
Figure 12 illustrates the current consumed during Sleep
mode. During the 125
s, the device is fully active and switch
states are read. The quiescent current is calculated by
integrating the normal running current over scan period plus
approximately 60
A.
Figure 12. Sleep Current Waveform
TEMPERATURE MONITOR
With multiple switch inputs closed and the device
programmed with the wetting current timers disabled,
considerable power will be dissipated by the IC. For this
reason temperature monitoring has been implemented. The
temperature monitor is active in the Normal mode only. When
the IC temperature is above the thermal limit, the temperature
monitor will do all of the following:
Generate an interrupt.
Force all wetting current sources to revert to 2.0 mA/
4.0 mA sustain currents
Maintain the 2.0 mA/4.0 mA sustain currents and all
other functionality.
Set the thermal flag bit in the SPI output register.
The thermal flag bit in the SPI word will be cleared on the
rising edge of CS provided the die temperature has cooled
below the thermal limit. When die temperature has cooled
below thermal limit, the device will resume previously
programmed settings.
Table 19. Interrupt Timer
Bits 543
Interrupt Period
000
32 ms
001
64 ms
010
128 ms
011
256 ms
100
512 ms
101
1.024 s
110
2.048 s
111
No interrupt wake-up
Table 20. Scan Timer
Bits 210
Scan Period
000
No Scan
001
1.0 ms
010
2.0 ms
011
4.0 ms
100
8.0 ms
101
16 ms
110
32 ms
111
64 ms
Inputs active for 125 us
out of 32 ms
I=V/R or 0.270V/100ohm = 2.7mA
I=V/R or 6mV/100ohm = 60 uA
Inputs active for 125 us
out of 32 ms
I=V/R or 0.270V/100ohm = 2.7mA
I=V/R or 6mV/100ohm = 60 uA
Inputs active for 125 us
out of 32 ms
I=V/R or 0.270V/100ohm = 2.7mA
I=V/R or 6mV/100ohm = 60 uA
I=V/R or 0.270V/100
=2.7mA
Inputs active for
125
s out of 32ms
I=V/R or
6.0mV/100
=60A
相關PDF資料
PDF描述
MS3100A32-9P CONN RCPT 14POS WALL MNT W/PINS
MS27473T22B21S CONN PLUG 21POS STRAIGHT W/SCKT
51426-1 CONN PLUG SHV RG-58 DUAL CRMP AU
MC33975TEK IC SWITCH DETECT MULT 32-SOIC
VI-JTM-IW-F3 CONVERTER MOD DC/DC 10V 100W
相關代理商/技術參數
參數描述
MC33975EK 功能描述:多路器開關 IC EMSDI RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MC33975EKR2 功能描述:多路器開關 IC EMSDI RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MC33975TEK 功能描述:接口 - 專用 MULTI SW DETECT INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MC33975TEKR2 功能描述:接口 - 專用 MULTI SW DETECT INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MC33981ABHFK 功能描述:電源開關 IC - 配電 HF 4.0MOHM RDSON SWITCH RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*