INTRODUCTION from first device is connected to SI o" />
參數資料
型號： MC33972ATEKR2
廠商： Freescale Semiconductor
文件頁數： 17/32頁
文件大?。?/td> 0K
描述： IC SWITCH DETECT SPI 32-SOIC
標準包裝： 1,000
應用： 開關監控
接口： SPI 串行
電源電壓： 3.1 V ~ 5.25 V
封裝/外殼： 32-SSOP（0.295"，7.50mm 寬）裸露焊盤
供應商設備封裝： 32-SOICW 裸露焊盤
包裝： 帶卷 (TR)
安裝類型： 表面貼裝
Analog Integrated Circuit Device Data
24
Freescale Semiconductor
33972
TYPICAL APPLICATIONS
INTRODUCTION
from first device is connected to SI of second device). With
two devices, 48 clock pulses are required to shift data in.
When the WAKE feature is used to enable the power supply,
both WAKE pins should be connected to the enable pin on the
power supply. The INT pins may be connected to one
interrupt pin on the MCU or may have their own dedicated
interrupt to the MCU.
The transition from Normal to Sleep mode is done by
sending the sleep command. With the devices connected in
serial and the sleep command sent, both will enter Sleep
mode on the rising edge of CS. When Sleep mode is entered,
the WAKE pin will be logic [1]. If either device wakes up, the
WAKE
pin will transition LOW, waking the other device.
A condition exists where the MCU is sending the sleep
command (CS logic [0]) and a switch input changes state.
With this event the device that detects this input will not
transition to Sleep mode, while the second device will enter
Sleep mode. In this case two switch status commands must
be sent to receive accurate switch status data. The first
switch status command will wake the device in Sleep mode.
Switch status data may not be valid from the first switch
status command because of the time required for the input
voltage to rise above the 4.0 V input comparator threshold.
This time is dependant on the impedance of SGn or SPn
node. The second switch status command will provide
accurate switch status information. It is recommended that
software wait 10 to 20 ms between the two switch status
commands, allowing time for switch input voltages to
stabilize. With all switch states acknowledged by the MCU,
the sleep sequence may be initiated. All parameters for Sleep
mode should be updated prior to sending the sleep
command.
The 33972 IC has an internal 5.0 V supply from the VPWR
pin. A POR circuit monitors the internal 5.0 V supply. In the
event of transients on the VPWR pin, an internal reset may
occur. Upon reset the 33972 will enter Normal mode with the
internal registers as defined in Table 15, page 18. Therefore
it is recommended that the MCU periodically update all
registers internal to the IC.
USING THE WAKE FEATURE
The 33972 provides a WAKE output and wake-up input
designed to control an enable pin on system power supply.
While in the Normal mode, the WAKE output is LOW,
enabling the power supply. In the Sleep mode, the WAKE pin
is high, disabling the power supply. The WAKE pin has a
passive pull-up to the internal 5.0 V supply but may be pulled
up through a resistor to the VPWR supply (see Figure 17,
When the WAKE output is not used, the pin should be
pulled up to the VDD supply through a resistor as shown in
During the Sleep mode, a switch closure will set the WAKE
pin LOW, causing the 33972 to enter the Normal mode. The
power supply will then be activated, supplying power to the
VDD pin and the microprocessor and the 33972. The
microprocessor can determine the source of the wake-up by
reading the interrupt flag.
COST AND FLEXIBILITY
Systems requiring a significant number of switch
interfaces have many discrete components. Discrete
components on standard PWB consume board space and
must be checked for solder joint integrity. An integrated
approach reduces solder joints, consumes less board space,
and offers wider operating voltage, analog interface
capability, and greater interfacing flexibility.
相關PDF資料
PDF描述
VE-B0P-IX-F2 CONVERTER MOD DC/DC 13.8V 75W
PIC16LC710-04/SS IC MCU OTP 512X14 A/D 20SSOP
VE-B0P-IX-F1 CONVERTER MOD DC/DC 13.8V 75W
V150A48E500BL CONVERTER MOD DC/DC 48V 500W
VE-B0N-IX-F4 CONVERTER MOD DC/DC 18.5V 75W
相關代理商/技術參數
參數描述
MC33972ATEW 功能描述:接口 - 專用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MC33972ATEWR2 功能描述:接口 - 專用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MC33972DWB 功能描述:IC SWITCH DETECT SPI 32-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
MC33972DWBR2 功能描述:IC SWITCH DETECT SPI 32-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
MC33972EW 功能描述:多路器開關 IC MSDISW RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*