- 您現在的位置：買賣IC網 > PDF目錄11725 > MC33884DW (Freescale Semiconductor)IC SWITCH SDI MONITOR 24-SOIC PDF資料下載
參數資料
| 型號： | MC33884DW |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 7/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH SDI MONITOR 24-SOIC |
| 標準包裝： | 30 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
33884
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
TRI-STATE COMMAND
This command places an external switch into a Tri-State
condition, essentially disconnecting the wetting current (if the
switch is metallic) and the sustain current. The internal input-
threshold comparator is still internally connected to its
external pin. This command does not change the mode of
operation
CP[4:1] – CONFIGURE PROGRAMMABLE SWITCH
Configure the programmable inputs SP[4:1] to detect
either an external switch-to-ground (internal current source)
or an external switch-to-battery (internal current sink).
Note: This configuration may be entered in any of the three
valid Operating Modes (see MOD[2:1]) within the Run
command.
(e.g., a Tri-State command received while in the Polling
mode leaves the part in that mode).
Note: The Tri-State register clears all bits to logic [0] (all
inputs in Tri-State) in response to a hardware reset; all inputs
also remain in Tri-State after existing the Sleep mode.
METALLIC COMMAND
This command enables the pulsed wetting current for an
external metallic switch and disables it for an external non-
metallic switch. This command does not change the mode of
operation (e.g., a Metallic command received while in Polling
mode leaves the part in that mode). Note that the Run
register values are unknown after exiting the Sleep mode.
Table 11. Programmable Switch Bit Definition
CPx
External Switch to:
0
Ground
1
Battery
Table 12. Tri-State Command
MSB
LSB
Command
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Tri-State
0
1
TG6
TG5
TG4
TG3
TG2
TG1
TP4
TP3
TP2
TP1
TB2
TB1
Reset Values:
Run Register
—
0
TG[6:1] = Tri-state switch-to-ground
TB[2:1] = Tri-state switch-to-battery
TP[4:1] = Tri-state programmable switch
Table 13. Programmable Switch Bit Definition
TGx, TBx, TPx
Input Configured to:
0
Input Disabled (Default)
1
Input Enabled
Table 14. Metallic Command
MSB
LSB
Command
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Metallic
0
1
0
1
MG6
MG5
MG4
MG3
MG2
MG1
MP4
MP3
MP2
MP1
MB2
MB1
Reset Values:
Run Register
—
U
U = Unknown value coming out of Sleep mode. It must be configured with Run command.
MG[6:1] = Metallic switch-to-ground
MB[2:1] = Metallic switch-to-battery
MP[4:1] = Metallic programmable switch
Table 15. Metallic Switch Bit Definition
MGx, MBx, MPx
Accept Switch Type:
0
Non-Metallic
1
Metallic (Enable Wetting Current Pulse)
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26MB99PA | CONN PLUG 7POS STRAIGHT W/PINS |
| MC33399D | IC LIN INTERFACE W/WAKE 8-SOIC |
| ATTINY88-AU | MCU AVR 8K ISP FLASH 1.8V 32TQFP |
| MS27497E22B55S | CONN RCPT 55POS WALL MNT W/SCKT |
| ATTINY48-MMH | MCU AVR 4KB FLASH 12MHZ 28-VQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33886DH | 功能描述:IC H-BRIDGE 5.0A OUTPUT 20-HSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| MC33886DHR2 | 功能描述:IC H-BRIDGE 5.0A 20-HSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| MC33886PVW | 功能描述:馬達/運動/點火控制器和驅動器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33886PVWR2 | 功能描述:馬達/運動/點火控制器和驅動器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33886VW | 功能描述:馬達/運動/點火控制器和驅動器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。