- 您現在的位置：買賣IC網 > PDF目錄359731 > MC33742SDWR2 (Motorola, Inc.) System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver PDF資料下載
參數資料
| 型號： | MC33742SDWR2 |
| 廠商： | Motorola, Inc. |
| 元件分類： | CAN |
| 英文描述： | System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver |
| 中文描述： | 系統基礎芯片的增強型（SBC）的高速CAN收發器 |
| 文件頁數： | 23/52頁 |
| 文件大?。?/td> | 1087K |
| 代理商： | MC33742SDWR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
33742
23
Reset and Watchdog Operation
Table 3
describes watchdog and reset output modes of
operation.
RST
is activated in the event V
DD
fall or watchdog is
not triggered.
WDOG
output is active LOW as soon as
RST
goes
LOW and stays LOW as long as the watchdog is not properly
reactivated by SPI. The
WDOG
output terminal is a push-pull
structure that can drive external components of the application;
for instance, to signal MCU wrong operation.
Figure 9
illustrates the device behavior in the event the TIM1
register in not properly accessed. In this case a software reset
occurs, and the
WDOG
terminal is set LOW until the TIM1
register is properly accessed.
Figure 9.
RST
and
WDOG
Output Operation
Wake-Up Capabilities
Several wake-up capabilities are available to the 33742
when it is in Sleep or Stop mode. When a wake-up has
occurred, the wake-up event is stored in the Wake-Up Register
(WUR) or the CAN register. The MCU can then access the
wake-up source. The wake-up options are selectable through
SPI while the 33742 is in Normal or Standby mode and prior to
entering low power mode (Sleep or Stop mode). When a wake-
up occurs from Sleep mode, the 33742 activates V
DD
. It
generates an interrupt if wake-up occurs from Stop mode.
Wake-Up from Wake-Up Inputs (L0:L3) Without Cyclic
Sense
The wake-up lines are dedicated to sense the state of
external switches and if changes occur to wake up the MCU (in
Sleep or Stop modes). Wake-up terminals L0:L3 are able to
handle 40 VDC. The internal threshold is 3.0 V typical and
these inputs can be used as an input port expander. The wake-
up input states are read through SPI (WUR register).
In order to select and activate direct wake-up from the L0:L3
inputs, the WUR register must be configured with the
appropriate level sensitivity. Additionally, the Low Power
Control (LPC) Register must be configured with 0xx0 data (bits
LX2HS and HSAUTO are set to 0).
Level sensitivity is selected by the WUR register. Level
sensitivity is configured by L0:L3 input pairs: L0 and L1 level
sensitivity are configured together, while L2 and L3 are
configured together.
Cyclic Sense Wake-Up (Cyclic Sense Timer and Wake-Up
Inputs L0:L3)
The 33742 can wake up upon state change of one of the four
wake-up input lines (L0:L3) while the external pullup or
pulldown resistor of the switches associated with the wake-up
input lines are biased with HS V
SUP
switch. The HS switch is
activated in Sleep or Stop modes from an internal timer. Cyclic
Sense and Forced Wake-Up are exclusive. If Cyclic Sense is
enabled, Forced Wake-Up cannot be enabled.
In order to select and activate the cyclic sense wake-up from
the L0:L3 inputs, the WUR register must be configured with the
appropriate level sensitivity, and the LPC register must be
configured with 1xx1 data (bit LX2HS set at 1 and bit HSAUTO
set at 1). The wake-up mode selection (direct or cyclic sense) is
valid for all four wake-up inputs.
Table 3. Watchdog and Reset Output Operation
Events
WDOG
Output
RST
Output
Device Power-Up
LOW to HIGH
LOW to HIGH
V
DD
Normal,
Watchdog Properly Triggered
HIGH
HIGH
V
DD
<
RST
TH
HIGH
LOW
Watchdog Timeout Reached
LOW
(Note 41)
LOW
Notes
41.
WDOG
stays LOW until the TIM1 register
is properly
addressed through SPI.
RST
WDOG
V
DD
SPI
SPI
CS
Watchdog Timeout
TIM1 register addressed.
Watchdog
Period
Watchdog Clear
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33742SDW | System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver |
| MMA6260 | ECONOLINE: RB & RA - Dual Output from a Single Input Rail- Power Sharing on Output- Industry Standard Pinout- 1kVDC & 2kVDC Isolation- Custom Solutions Available- UL94V-0 Package Material- Efficiency to 85% |
| MMA6260Q | 【1.5g Dual Axis Micromachined Accelerometer |
| MMA6261Q | 【1.5g Dual Axis Micromachined Accelerometer |
| MC68HC11A0 | 8-Bit Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33742SPEG | 功能描述:CAN 接口集成電路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33742SPEGR2 | 功能描述:CAN 接口集成電路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33761SNT1025 | 制造商:ON SEMI 功能描述:New |
| MC33761SNT1-025 | 功能描述:低壓差穩壓器 - LDO 2.5V 80mA Output RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MC33761SNT1-025G | 功能描述:低壓差穩壓器 - LDO 2.5V 80mA Output w/Enable Low Noise RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。