- 您現在的位置：買賣IC網 > PDF目錄371030 > MC33593 (Motorola, Inc.) PLL Tuned UHF Receiver for Data Transfer Applications PDF資料下載
參數資料
| 型號： | MC33593 |
| 廠商： | Motorola, Inc. |
| 英文描述： | PLL Tuned UHF Receiver for Data Transfer Applications |
| 中文描述： | 鎖相環調諧UHF接收器的數據傳輸應用 |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 681K |
| 代理商： | MC33593 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
N
Go to: www.freescale.com
revision 7.0, 5 February 2002
Motorola, Inc., 2002.
SERIAL INTERFACE
ROMEO2 and the microcontroller communicate through a Serial Peripheral Interface (SPI). It enables:
- the microcontroller to set and check ROMEO2 configuration,
- ROMEO2 to send the received data.
If the SPI is not used, a Power On Reset (POR) sets ROMEO2 to operate correctly in a default configuration.
The interface is operated by the 3 following input/output pins:
- Serial Clock SCLK,
- Master Output Slave Input MOSI,
- Master Input Slave Output MISO.
The master clock is used to synchronise data movement both in and out of the device through its MOSI and
MISO lines. The master and slave devices are capable of exchanging a byte of information during a sequence of
eight clock cycles. Since SCLK is generated by the master device, this line is an input on a slave device.
The MISO line is configured as an input in a master device and as an output in a slave device. The MOSI line is
configured as an output in a master device and as an input in a slave device. The MISO and MOSI lines transfer
serial data in one direction with the most significant bit sent first. Data are captured on falling edges of SCLK.
Data are shifted out on rising edge of SCLK. When no data are output, SCLK and MOSI force a low level. Using
Motorola acronyms, this means that the clock phase and polarity control bits of the microcontroller SPI have to be
CPOL= 0 and CPHA=1.
In configuration mode, as long as a low level is applied on RESETB (see state machine on figure 14 page 13),
the microcontroller is the master node providing clock information on SCLK input, control and configuration bits
on the MOSI line. If the default configuration is not the desired one, the microcontroller (MCU) can change it by
writing into the configuration registers. The configuration registers can also be read back to check their contents.
Configuration registers cannot be addressed separately, the whole configuration has to be sent as a 3x8
bitstream. The contents are written out as a 24-bit serial data stream. Transmissions which are not multiple of 24
bits may lead to unexpected configurations. The first bit transmitted on MOSI does not change the content of the
configuration registers. Note that a low level applied on RESETB does not affect the configuration register
content.
When RESETB is set to a high level, if Data Manager is enabled (DME=1), ROMEO2 becomes master and
sends received data on the MOSI line and the recovered clock on SCLK. It is then recommended that the MCU
SPI is set as slave. If the data received does not fit in an entire number of bytes, the data manager will fill the last
byte. If the data received constitute an whole number of bytes, the data manager may generate and send an
extra byte whose content is irrelevant. If DME=0, the SPI is disabled. Raw data is sent on the MOSI line.
When ROMEO2 SPI is changed from master (run mode) to slave (configuration mode) or from slave to
master, it is recommended that the MCU SPI is set as slave before the mode transition.
At power-on, the POR resets the internal registers. This defines the receiver default configuration (see gray
rows on tables 4, 7 & 8). In this configuration, the SPI is disabled and ROMEO2 sends raw data on the MOSI line.
This default configuration enables the circuit to operate as a standalone receiver without any external control.
After POR, RESETB forces a low level. Therefore an external pull-up resistor should be used in order to avoid
entering configuration mode.
Figure 12: Writing into configuration registers
MOSI line
CR1
CR2
CR3
0
SCLK line
MCU (master)
ROMEO2
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33593FTA | PLL Tuned UHF Receiver for Data Transfer Applications |
| MC3361B | Low Power Narrowband FM IF Receiver(低功耗窄帶FM IF接收器) |
| MC3361C | Low Power Narrowband FM IF Receiver(低功耗窄帶FM IF接收器) |
| MC3361 | LOW POWER NARROWBAND FM IF |
| MC3361BD | LOW POWER NARROWBAND FM IF |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33593FTAE | 功能描述:射頻接收器 UHF RECEIVER RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| MC33593FTAER2 | 功能描述:射頻接收器 UHF RECEIVER RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| MC33593MOD868EV | 功能描述:開發板和工具包 - 無線 MC33593 (ROMEO2) RF EVAL RoHS:否 制造商:Arduino 產品:Evaluation Boards 工具用于評估:AT32UC3L 核心:AVR32 頻率: 接口類型:USB 工作電源電壓:5 V |
| MC33594FTA | 功能描述:射頻接收器 315 434 MHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| MC33594FTAE | 功能描述:射頻接收器 UHF RECEIVER RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。