- 您現在的位置：買賣IC網 > PDF目錄359732 > MC33486 (Motorola, Inc.) Dual High Side Switch for H-Bridge Automotive Applications PDF資料下載
參數資料
| 型號： | MC33486 |
| 廠商： | Motorola, Inc. |
| 英文描述： | Dual High Side Switch for H-Bridge Automotive Applications |
| 中文描述： | 雙通道高邊開關的H橋汽車應用 |
| 文件頁數： | 2/9頁 |
| 文件大?。?/td> | 392K |
| 代理商： | MC33486 |
MC33486
PINS FUNCTION DESCRIPTION
Dual High Side Switch for H-Bridge Automotive Applications
2
Pin No.
Name/Function
Description
TAB
V
bat
Supply Voltage
The backside TAB is connected to the power supply of the
MC33486DH. In addition to its supply function, the tab contributes to
the thermal behaviour of the device by conducting the heat from the
switching MOSFET to the printed circuit board.
5,6,7,8
13,14,15,16
OUT1
OUTPUT Channel 1
OUT 2
OUTPUT Channel 2
Pins 5, 6,7,8 are the source of the output1 15mOhm High-side
MOSFET1. Pins 13,14,15 are source of the output 2 15mOhm High-side
MOSFET2. They are respectively controlled via the IN1 and IN2 pins.
These outputs are current limited and thermally protected
3
18
IN 1
INPUT Channel 1
IN 2
INPUT Channel 2
These are the device input pins which directly control their associated
outputs. The levels are CMOS compatible. When the input is a logic
low, the associated output is low (High Side OFF and Low Side ON).
Each input pin has an internal active pull down, so that it will not float
if disconnected.
19
St
Status for both
Channels
The Status output is an open drain indication that goes active low
when a fault mode (Short to gnd/Vbat, Overtemp) is detected by the
device on either one channel or both simultaneously. Its internal
structure is an open drain architecture with an internal clamp at 6V.
An external pull up resistor connected to Vdd (5V) is needed. See
Functional Truth Table.
4
17
GLS1
GLS2
These pins have to be connected to the gate of each Low Side. When the
input (INx) is logic High, the associated GLS is grounded to turn off the
external FET .
20
Wake
This pin is a digital input . When Wake is a logic low, the device
’
s bias current
draw is at a minimum. If Wake is a logic high, the part is operationnal. Wake
pin has a pull down resistor.
2
Cur R
Load Current Sense
The Current Sense pin deliver a ratioed amount (1/3700) of the sum
of the High Side currents that can be used to generate signal ground
referenced output voltages for use by the microcontroller.
9, 10, 11, 12,
NC
Not Connected
These pins are not used.
1
GND
GROUND
This is the Ground pin of the device.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33099 | Regulating Pulse-Width Modulators 16-SOIC 0 to 70 |
| MC68HC11 | 8-Bit Microcontrollers |
| MMA1213D | Surface Mount Micromachined Accelerometer |
| MMA1213DR2 | Surface Mount Micromachined Accelerometer |
| MC68HC11Ax | 8-Bit Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33486ADH | 功能描述:電源開關 IC - 配電 DUALHIGH-SIDE BRIDGE RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MC33486ADHR2 | 功能描述:電源開關 IC - 配電 DUALHIGH-SIDE BRIDGE RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MC33486DH | 功能描述:IC SWITCH DUAL H-SIDE 20-HSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| MC33493ADTBE | 功能描述:射頻發射器 UHF TRANSMITTER RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| MC33493ADTBER2 | 功能描述:射頻發射器 UHF TRANSMITTER RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。