參數資料
型號: MC33288
廠商: Motorola, Inc.
英文描述: Solid State Relay for Automotive Flasher Applications
中文描述: 固態繼電器汽車閃光器應用
文件頁數: 2/8頁
文件大?。?/td> 382K
代理商: MC33288
MC33288
PINS FUNCTION DESCRIPTION
Solid State Relay for Automotive Flasher Applications
Go to: www.freescale.com
2
Pin No.
Name/Function
Description
TAB
V
bat
Supply Voltage
The backside TAB is connected to the power supply of the
MC33288DH. In addition to its supply function, this pin contributes to
the thermal behaviour of the device by conducting the heat from the
switching MOSFET to the printed circuit board.
6,7,8
13,14,15
OUT1
OUTPUT Channel 1
OUT 2
OUTPUT Channel 2
Pins 6,7,8 are the source of the output1 25mOhm MOSFET1. Pins
13,14,15 are source of the output 2 25mOhm MOSFET2. They deliver
current to the connected loads and are respectively controlled via the
IN1 and IN2 pins. These outputs are current limited and thermally
protected.
3
18
IN 1
INPUT Channel 1
IN 2
INPUT Channel 2
These are the device input pins which directly control their associated
outputs. The levels are CMOS compatible. When the input is a logic
low, the associated output MOSFET is in the off state. When input is
high, the MOSFET is turned on and the load is activated.
When both inputs are low, the device is in standby mode and its
supply current is reduced. Each input pin has an internal active pull
down, so that it will not float if disconnected.
19
Status
Status for both
Channels
The Fault output is an open drain indication that goes active low when
a fault mode (Openload, Overtemp) is detected by the device on
either one channel or both simultaneously. Its internal structure is an
open drain architecture with an internal clamp at 6V. An external pull
up resistor connected to Vdd (5V) is needed. See Functional Truth
Table.
20
Wlp
Warning Lamp Output
This pin is the source of a 3.2 Ohm MOSFET. This output is current
limited and thermally protected. It delivers current through the
connected load when both IN1 and IN2 inputs are logic high. It is usually
used as a warning lamp driver for Flasher application.
2
Cur R
Load Current Sense
The Current Sense pin deliver a ratioed amount (1/1000) of the sum
of the currents that can be used to generate signal ground referenced
output voltages for use by the microcontroller.
4, 9, 10, 11, 12, 17
NC
Not Connected
These pins are not used.
5, 16
DNC
Do Not Connect
These pins must not be connected.
11
GND
GROUND
This is the Ground pin of the device.
Freescale Semiconductor, Inc.
相關PDF資料
PDF描述
MC33288DH Solid State Relay for Automotive Flasher Applications
MC33288DHR2 Solid State Relay for Automotive Flasher Applications
MC68HC11D0 Microcontrollers
MC68HC11D0CFB2 Microcontrollers
MC68HC11D0CFB3 Microcontrollers
相關代理商/技術參數
參數描述
MC33288ADH 制造商:Freescale Semiconductor 功能描述:POWER SWITCH HI SIDE 40A 22-PIN (20+2TAB) HSOP - Rail/Tube
MC33288ADHR2 制造商:Freescale Semiconductor 功能描述:POWER SWITCH HI SIDE 40A 22-PIN (20+2TAB) HSOP T/R - Tape and Reel
MC33288DDH 功能描述:電源開關 IC - 配電 FLASHER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MC33288DDHR2 功能描述:電源開關 IC - 配電 FLASHER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MC33289 制造商:SPC Multicomp 功能描述:HEATSINK TO220 10.2/W 3 HOLES 制造商:SPC Multicomp 功能描述:HEATSINK TO220 10.2C/W 3 HOLES 制造商:SPC Multicomp 功能描述:HEAT SINK; Packages Cooled:TO-220; Thermal Resistance:10.2C/W; External Height - Imperial:1.496"; External Height - Metric:38mm; External Width - Imperial:1.358"; External Width - Metric:34.5mm; External Length - Imperial:0.492" ;RoHS Compliant: Yes