- 您現在的位置：買賣IC網 > PDF目錄382302 > MC33269ST-3.3T3 (ON SEMICONDUCTOR) 800 mA, Adjustable Output, Low Dropout Voltage Regulator PDF資料下載
參數資料
| 型號： | MC33269ST-3.3T3 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 800 mA, Adjustable Output, Low Dropout Voltage Regulator |
| 中文描述： | 3.3 V FIXED POSITIVE LDO REGULATOR, 1.35 V DROPOUT, PSSO3 |
| 封裝： | SOT-223, 3 PIN |
| 文件頁數： | 7/14頁 |
| 文件大?。?/td> | 133K |
| 代理商： | MC33269ST-3.3T3 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
MC33269, NCV33269
http://onsemi.com
7
APPLICATIONS INFORMATION
Figures 11 through 15 are typical application circuits. The
output current capability of the regulator is in excess of
800 mA, with a typical dropout voltage of less than 1.0 V.
Internal protective features include current and thermal
limiting.
* The MC33269 requires an external output capacitor for
stability. The capacitor should be at least 10 F with an
equivalent series resistance (ESR) of less than 10
greater than 0.2
over the anticipated operating
temperature range. With economical electrolytic capacitors,
cold temperature operation can pose a problem. As
temperature decreases, the capacitance also decreases and
the ESR increases, which could cause the circuit to oscillate.
Also capacitance and ESR of a solid tantalum capacitor is
more stable over temperature. The use of a low ESR ceramic
capacitor placed within close proximity to the output of the
device could cause instability.
** An input bypass capacitor is recommended to improve
transient response or if the regulator is connected to the
but
supply input filter with long wire lengths. This will reduce
the circuit’s sensitivity to the input line impedance at high
frequencies. A 0.33 F or larger tantalum, mylar, ceramic,
or other capacitor having low internal impedance at high
frequencies should be chosen. The bypass capacitor should
be mounted with shortest possible lead or track length
directly across the regulator’s input terminals.
Applications
should be tested over all operating conditions to insure
stability.
Internal thermal limiting circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated, typically at
170
°
C, the output is disabled. There is no hysteresis built
into the thermal limiting circuit. As a result, if the device is
overheating, the output will appear to be oscillating. This
feature is provided to prevent catastrophic failures from
accidental device overheating.
It is not intended to be used
as a substitute for proper heatsinking.
Figure 11. Typical Fixed Output Application
MC33269XX
V
in
V
out
GND
C
o
10 F
An input capacitor is not necessary for stability, however
it will improve the overall performance.
Figure 12. Typical Adjustable Output Application
MC33269
V
in
V
out
Adj
C
o
10 F
C
Adj
***
R1
R2
***C
Adj
is optional, however it will improve the ripple rejection.
The MC34269 develops a 1.25 V reference voltage between the
output and the adjust terminal. Resistor R1, operates with
constant current to flow through it and resistor R2. This current
should be set such that the Adjust Pin current causes negligible
drop across resistor R2. The total current with minimum load
should be greater than 8.0 mA.
Figure 13. Current Regulator
MC33269
V
in
I
out
Adj
R
S
Iout
Figure 14. Battery BackedUp Power Supply
MC33269XX
V
in
V
out
MC33269XX
GND
C
o
10 F
Figure 15. Digitally Controlled Voltage Regulator
MC33269
V
in
V
out
Adj
C
o
10 F
R1
R2
R
2
sets the maximum output voltage. Each transistor
reduces the output voltage when turned on.
The Schottky diode in series with the ground leg of the upper
regulator shifts its output voltage higher by the forward
voltage drop of the diode. This will cause the lower device
to remain off until the input voltage is removed.
Vout
1.25
1
R2
R1
IAdjR2
1.25
RS
C
in
C
in
C
in
C
o
10 F
C
in
C
in
GND
C
in
**
**
**
**
**
**
*
*
*
*
*
相關PDF資料 |
PDF描述 |
|---|---|
| MC33275ST-3.0T3 | LOW DROPOUT MICROPOWER VOLTAGE REGULATOR |
| MC33275DT-2.5RK | LOW DROPOUT MICROPOWER VOLTAGE REGULATOR |
| MC33275DT-3.0RK | LOW DROPOUT MICROPOWER VOLTAGE REGULATOR |
| MC33275DT-3.3RK | LOW DROPOUT MICROPOWER VOLTAGE REGULATOR |
| MC33275DT-5.0RK | LOW DROPOUT MICROPOWER VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33269T | 功能描述:低壓差穩壓器 - LDO 1.35-10V ADJ 800mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MC33269T-012 | 功能描述:低壓差穩壓器 - LDO 12V ADJ 800mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MC33269T-012G | 功能描述:低壓差穩壓器 - LDO 12V ADJ 800mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MC33269T-3.3 | 功能描述:低壓差穩壓器 - LDO 3.3V ADJ 800mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MC33269T-3.3G | 功能描述:低壓差穩壓器 - LDO 3.3V ADJ 800mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。