- 您現在的位置：買賣IC網 > PDF目錄385566 > MC33025DWR2 (ON SEMICONDUCTOR) High Speed Double−Ended PWM Controller PDF資料下載
參數資料
| 型號： | MC33025DWR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | High Speed Double−Ended PWM Controller |
| 中文描述： | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 482K |
| 代理商： | MC33025DWR2 |
MC34025, MC33025
http://onsemi.com
8
OPERATING DESCRIPTION
The MC33025 and MC34025 series are high speed, fixed
frequency, doubleended pulse width modulator controllers
optimized for high frequency operation. They are
specifically designed for OffLine and DCtoDC
converter applications offering the designer a cost effective
solution
with
minimal
representative block diagram is shown in Figure 19.
external
components.
A
Oscillator
The oscillator frequency is programmed by the values
selected for the timing components R
T
and C
T
. The R
T
pin
is set to a temperature compensated 3.0 V. By selecting the
value of R
T
, the charge current is set through a current mirror
for the timing capacitor C
T
. This charge current runs
continuously through C
T
. The discharge current ratio is to be
10 times the charge current, which yields the maximum duty
cycle of 90%. C
T
is charged to 2.8 V and discharged to 1.0
V. During the discharge of C
T
, the oscillator generates an
internal blanking pulse that resets the PWM Latch, inhibits
the outputs, and toggles the steering flipflop. The threshold
voltages on the oscillator comparator is trimmed to
guarantee an oscillator accuracy of 5.0% at 25
°
C.
Additional dead time can be added by externally
increasing the charge current to C
T
as shown in Figure 24.
This changes the charge to discharge ratio of C
T
which is set
internally to I
charge
/10 I
charge
. The new charge to discharge
ratio will be:
% Deadtime
Iadditional
10 (Icharge)
Icharge
A bidirectional clock pin is provided for synchronization
or for master/slave operation. As a master, the clock pin
provides a positive output pulse during the discharge of C
T
.
As a slave, the clock pin is an input that resets the PWM latch
and blanks the drive output, but does not discharge C
T
.
Therefore, the oscillator is not synchronized by driving the
clock pin alone. Figures 30 and 31 provide suggested
synchronization.
Error Amplifier
A fully compensated Error Amplifier is provided. It
features a typical DC voltage gain of 95 dB and a gain
bandwidth product of 8.3 MHz with 75 degrees of phase
margin (Figure 4). Typical application circuits will have the
noninverting input tied to the reference. The inverting input
will typically be connected to a feedback voltage generated
from the output of the switching power supply. Both inputs
have a Common Mode Voltage (V
CM
) input range of 1.5 V
to 5.5 V. The Error Amplifier Output is provided for external
loop compensation.
SoftStart Latch
SoftStart is accomplished in conjunction with an
external capacitor. The soft start capacitor is charged by an
internal 9.0 A current source. This capacitor clamps the
output of the error amplifier to less than its normal output
voltage, thus limiting the duty cycle.
The time it takes for a capacitor to reach full charge is
given by:
(4.5
105) CSoft-Start
A SoftStart latch is incorporated to prevent erratic
operation of this circuitry. Two conditions can cause the
SoftStart circuit to latch so that the SoftStart capacitor
stays discharged. The first condition is activation of an
undervoltage lockout of either V
CC
or V
ref
. The second
condition is when current sense input exceeds 1.4 V. Since
this latch is “set dominant”, it cannot be reset until either of
these signals is removed, and the voltage at C
SoftStart
is less
than 0.5 V.
t
PWM Comparator and Latch
A PWM circuit typically compares an error voltage with
a ramp signal. The outcome of this comparison determines
the state of the output. In voltage mode operation the ramp
signal is the voltage ramp of the timing capacitor. In current
mode operation the ramp signal is the voltage ramp induced
in a current sensing element. The ramp input of the PWM
comparator is pinned out so that the user can decide which
mode of operation best suits the application requirements.
The ramp input has a 1.25 V offset such that whenever the
voltage at this pin exceeds the Error Amplifier Output
voltage minus 1.25 V, the PWM comparator will cause the
PWM latch to set, disabling the outputs. Once the PWM
latch is set, only a blanking pulse by the oscillator can reset
it, thus initiating the next cycle.
A toggle flip flop connected to the output of the PWM
latch controls which output is active. The flip flop is pulsed
by an OR gate that gets its inputs from the oscillator clock
and the output of the PWM latch. A pulse from either one
will cause the flip flop to enable the other output.
Current Limiting and Shutdown
A pin is provided to perform current limiting and
shutdown operations. Two comparators are connected to the
input of this pin. When the voltage at this pin exceeds 1.0 V,
one of the comparators is activated. The output of this
comparator sets the PWM latch, which disables the output.
In this way cyclebycycle current limiting is
accomplished. If a current limit resistor is used in series with
the power devices, the value of the resistor is found by:
RSense
1.0 V
Ipk (switch)
相關PDF資料 |
PDF描述 |
|---|---|
| MC33025DWR2G | High Speed Double−Ended PWM Controller |
| MC33025PG | High Speed Double−Ended PWM Controller |
| MC3302 | Single Supply Quad Comparators(四電壓比較器) |
| MC3303 | Single Supply Quad Operational Amplifiers(單電源四運放) |
| MC3403 | Quadruple Low Power Operational Amplifiers(四路低功率通用運放) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33025DWR2G | 功能描述:電流型 PWM 控制器 Dual Output Voltage or Current Mode PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC33025P | 功能描述:電流型 PWM 控制器 Dual Output Voltage RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC33025PG | 功能描述:電流型 PWM 控制器 Dual Output Voltage or Current Mode PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC33029 | 制造商:SPC Multicomp 功能描述:FAN POWER CORD 制造商:SPC Multicomp 功能描述:FAN POWER CORD; For Use With:Axial Fans; Voltage Rating:300V; Fan Side Connector:45 Angle Plug; Cable Length:120"; Accessory Type:Fan Power Cord; Equipment Side Connector:Blunt Cut Wire Leads; Supply Voltage:300V ;RoHS Compliant: Yes |
| MC3302-BI/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:13-Bit Differential Input, Low Power A/D Converter with SPI Serial Interface |
發布緊急采購，3分鐘左右您將得到回復。