- 您現在的位置：買賣IC網 > PDF目錄385566 > MC1H3 (Microchip Technology Inc.) High Voltage Power Module Users Guide PDF資料下載
參數資料
| 型號： | MC1H3 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | High Voltage Power Module Users Guide |
| 中文描述： | 高壓電源模塊用戶指南 |
| 文件頁數： | 16/60頁 |
| 文件大?。?/td> | 1522K |
| 代理商： | MC1H3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
dsPICDEM MC1H 3-Phase High Voltage Power Module
DS70096A-page 10
2003 Microchip Technology Inc.
1.2.4
Power-Up/Power-Down Sequence
The user should ensure that the following sequence are followed.
1.2.4.1
POWER-UP SEQUENCE
With the development board plugged in, turn on the power supply feeding the
control PCB (if not already on).
One or more of the fault lights may illuminate. This is normal.
Turn on the AC supply to the power module.
Reset the system by activating the active high ISO_RESET line. The ISO_RESET
line is on pin 33 of the 37-pin, D-type (see
Section 1.7 “User Signal Connector
Pinout (37-Pin, D-Type)”
). If using the dsPICDEM MC1 Motor Control
Development Board, this signal is routed to pin 14 of the 30F6010 dsPIC device,
which is on Port RE9. The minimum pulse width for the RESET is 2
μ
s. The
RESET should be done in coordination with the SPI handling routine of the
dsPIC device to ensure correct synchronization of the serial interface providing
the isolated voltage feedback (see
Section 1.2.6.2 “Isolated Feedback”
and
Section 1.4.7.2 “Isolated Voltage Feedback”
). The system is now ready to use.
1.2.4.2
POWER-DOWN SEQUENCE
Stop firing all power devices.
Turn off the incoming AC supply.
Wait until the red DC bus LED indicator visible through the ventilation holes in the
top of the unit has gone out (this will take 3 minutes or less).
Turn off the power supply feeding the control card (if required).
1.2.5
Power Device Switching Frequencies
The PFC stage has been designed for a switching frequency of 50 kHz (±5%).
This offers a good system compromise between cost, size and efficiency. The
modulation frequency affects not only the losses in the power switches and diode but
also that in the PFC inductor and snubbing components. The user should not deviate
from the stated carrier frequency. The user should note that a typical regulation level
for the DC bus is between 350-400V.
If the user does not wish to use the PFC stage the PFC switches can simply be
left off.
However, the PFC inductor and diode will be left in circuit and the input
current will remain limited to 5A (RMS) and 8.9A Peak. The user should read
Section
1.5.3.3 “Bypassing The PFC”
if this is unacceptable.
The Brake chopper switch has been designed so that it may be switched up to a
maximum frequency of 16 kHz.
This frequency limit is chosen for power dissipation
and low voltage power supply consumption reasons. In most braking applications a
lower modulation frequency will be used, as there is little benefit (apart from acoustic
noise) from modulating at such a high frequency.
The six inverter switches have been designed so that they may be switched up
to a maximum frequency of 20 kHz.
This frequency limit is chosen for power
dissipation and low voltage power supply consumption reasons. Unless extremely low
output current harmonics or very high bandwidth control is required, it is suggested
that a 16 kHz carrier frequency be used. This offers lower loss while still being
inaudible. It also has the advantage that the dead time insertion will cause less
distortion of the output voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33023DWG | High Speed Single−Ended PWM Controller |
| MC33023DWR2 | High Speed Single−Ended PWM Controller |
| MC33023DWR2G | High Speed Single−Ended PWM Controller |
| MC33025DWG | High Speed Double−Ended PWM Controller |
| MC33025DWR2 | High Speed Double−Ended PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1JJN0600 | 功能描述:環形公制連接器 M40 C Straight 6 Position Extension RoHS:否 制造商:3M Electronic Solutions Division 產品類型:Connectors 系列:M12 外殼類型:Plug 觸點數量:4 安裝風格:Cable 端接類型:Solder Cup 電流額定值:4 A |
| MC1JJN0800 | 功能描述:環形公制連接器 M40 C Straight Extension 8 Pos. RoHS:否 制造商:3M Electronic Solutions Division 產品類型:Connectors 系列:M12 外殼類型:Plug 觸點數量:4 安裝風格:Cable 端接類型:Solder Cup 電流額定值:4 A |
| MC1LKN0600 | 功能描述:環形公制連接器 M40 C Straight Recpt 6 Position RoHS:否 制造商:3M Electronic Solutions Division 產品類型:Connectors 系列:M12 外殼類型:Plug 觸點數量:4 安裝風格:Cable 端接類型:Solder Cup 電流額定值:4 A |
| MC1LKN0800 | 功能描述:環形公制連接器 M40 C Straight Recpt 8 Position RoHS:否 制造商:3M Electronic Solutions Division 產品類型:Connectors 系列:M12 外殼類型:Plug 觸點數量:4 安裝風格:Cable 端接類型:Solder Cup 電流額定值:4 A |
| MC1M | 制造商:G & J HALL 功能描述:STEP DRILL 4-12MM 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 4-12MM, 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 4-12MM, 1MM STEP; Drill Bit Size Metric:4mm; Overall Length:75.5mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Material:Steel; Material Thickness Max:5mm; Range:4mm - 12mm; Range:4mm - 12mm; Shank Dia:6mm; S ;RoHS Compliant: NA |
發布緊急采購，3分鐘左右您將得到回復。