- 您現在的位置：買賣IC網 > PDF目錄1947 > MC14600P (Freescale Semiconductor)IC ALARM GENERAL MONO 16-DIP PDF資料下載
參數資料
| 型號： | MC14600P |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ALARM GENERAL MONO 16-DIP |
| 標準包裝： | 25 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-PDIP |
| 包裝： | 管件 |
Analog Integrated Circuit Device Data
4
Freescale Semiconductor
14600
Archived by Freescale Semiconductor, Inc., 2009
Archive
Information
Archive
Information
DEVICE OPERATION
Timing
The internal oscillator of the MC14600 operates with a
period of 1.65 seconds during no-alarm conditions. Each
1.65 seconds, internal power is applied to the entire IC and a
check is made for an alarm input level except during LED
pulse, Low Battery Alarm Chirp, or Horn Modulation (in
alarm). Every 24 clock cycles a check is made for low battery
by comparing VDD to an internal zener voltage. Since very
small currents are used in the oscillator, the oscillator
capacitor should be of a low leakage type.
Detect Circuitry
If an alarm condition is detected, the oscillator period
becomes 41.67 ms and the piezoelectric horn oscillator
circuit is enabled. The horn output is modulated 167 ms on,
83 ms off. During the off time, alarm detect input (Pin 15) is
again checked and will inhibit further horn output if no alarm
condition is sensed. During alarm conditions the low battery
chirp is inhibited, and the LED pulses at a 1.0 Hz rate.
An active guard is provided on a pin adjacent to the detect
input (Pin 16). The voltage at this pin will be within 100 mV of
the input signal. Pin 16 will allow monitoring of the input signal
at pin 15 through a buffer. The active guard op amp is not
power strobed and thus gives constant protection from
surface leakage currents. Pin 15 (the Detect input) has
internal diode protection against static damage.
Low Battery Threshold
The low battery voltage level is set internally by a voltage
divider connected between VDD and VSS. This voltage can
be altered by external resistors connected from pin 3 to either
VDD or VSS. A resistor to VDD will decrease the threshold
while a resistor to GND will increase it.
Alarm Threshold (Sensitivity)
The alarm condition voltage level is set externally through
Pin 13. A voltage divider can be used to set the alarm trip
point. Pin 13 is connected internally to the negative input of
the detect comparator.
LED Pulse
The 9-volt battery level is checked every 40 seconds
during the LED pulse. The battery is loaded via a 10 mA
pulse for 10 ms. If the LED is not used, it should be replaced
with an equivalent resistor so that the battery loading remains
at 10 mA.
.
Figure 3. Typical Application Components
MC14600
116
2
3
4
5
6
7
8
15
14
13
12
11
10
9
330
Ω
RBIAS
0.1
μF
1.5 M
Ω*
0.001
μF
220 k
Ω*
COSC
DETECT
INPUT
R1
VDD
R2
RP
*Note: Component values may change depending on the type of piezoelectric horn used.
相關PDF資料 |
PDF描述 |
|---|---|
| MC1488DR2G | IC LINE DRIVER QUAD MONO 14-SOIC |
| MC1489AMELG | IC LINE RECEIVER QUAD 14-SOEIAJ |
| MC26LS30DR2G | IC DRIVER LINE CONFIG 16SOIC |
| MC33388D | IC CAN FAULT TOL INTRFACE 14SOIC |
| MC33389DDW | IC SYSTEM BASE W/CAN 28-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1460G | 制造商:Motorola Inc 功能描述: |
| MC-14632.768000KHZ | 制造商:Epson Electronics America Inc 功能描述: |
| MC-14632.768000KHZ7.0 | 制造商:SEIKO_EPSON 功能描述: |
| MC-146-32.7680K-A | 制造商:Epson Electronics America Inc 功能描述: |
| MC14632.7680K-A | 制造商:MAJOR 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。