- 您現在的位置：買賣IC網 > PDF目錄382297 > MC145018 (Motorola, Inc.) LONIZATION SMOKE DETECTOR IC WITH INTERCONNECT AND TEMPORAL HORN DRIVER PDF資料下載
參數資料
| 型號： | MC145018 |
| 廠商： | Motorola, Inc. |
| 英文描述： | LONIZATION SMOKE DETECTOR IC WITH INTERCONNECT AND TEMPORAL HORN DRIVER |
| 中文描述： | 電離煙霧報警器集成電路互連和顳角驅動 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 263K |
| 代理商： | MC145018 |
5
Motorola Sensor Device Data
DEVICE OPERATION
TIMING
The internal oscillator of the MC145018 operates with a
period of 1.65 seconds during no–smoke conditions. Each
1.65 seconds, internal power is applied to the entire IC and a
check is made for smoke, except during LED pulse, Low Bat-
tery Alarm Chirp, or Horn Modulation (in smoke). Every 24
clock cycles a check is made for low battery by comparing
V
DD
to an internal zener voltage. Since very small currents
are used in the oscillator, the oscillator capacitor should be of
a low leakage type.
DETECT CIRCUITRY
If smoke is detected, the oscillator period becomes
41.67 ms and the piezoelectric horn oscillator circuit is
enabled. The horn output is modulated 500 ms on, 500 ms
off. During the off time, smoke is again checked and will
inhibit further horn output if no smoke is sensed. During local
smoke conditions the low battery alarm is inhibited, but the
LED pulses at a 1.0 Hz rate. In remote smoke, the LED is
inhibited as well.
An active guard is provided on both pins adjacent to the
detect input. The voltage at these pins will be within 100 mV
of the input signal. This will keep surface leakage currents to
a minimum and provide a method of measuring the input volt-
age without loading the ionization chamber. The active guard
op amp is not power strobed and thus gives constant protec-
tion from surface leakage currents. Pin 15 (the Detect input)
has internal diode protection against static damage.
INTERCONNECT
The I/O (Pin 2), in combination with V
SS
, is used to inter-
connect up to 40 remote units for common signaling. A Local
Smoke condition activates a current limited output driver,
thereby signaling Remote Smoke to interconnected units. A
small current sink improves noise immunity during non–
smoke conditions. Remote units at lower voltages do not
draw excessive current from a sending unit at a higher volt-
age. The I/O is disabled for three oscillator cycles after power
up, to eliminate false alarming of remote units when the bat-
tery is changed.
SENSITIVITY/LOW BATTERY THRESHOLDS
Both the sensitivity threshold and the low battery voltage
levels are set internally by a common voltage divider (see
Figure 1) connected between V
DD
and V
SS
. These voltages
can be altered by external resistors connected from pins 3 or
13 to either V
DD
or V
SS
. There will be a slight interaction here
due to the common voltage divider network. The sensitivity
threshold can also be set by adjusting the smoke chamber
ionization source.
TEST MODE
Since the internal op amps and comparators are power
strobed, adjustments for sensitivity or low battery level could
be difficult and/or time–consuming. By forcing Pin 12 to V
SS
,
the power strobing is bypassed and the output, Pin 1,
constantly shows smoke/no smoke. Pin 1 = V
DD
for smoke.
In this mode and during the 10 ms power strobe, chip current
rises to approximately 50
μ
A.
LED PULSE
The 9–volt battery level is checked every 40 seconds dur-
ing the LED pulse. The battery is loaded via a 10 mA pulse
for 11.6 ms. If the LED is not used, it should be replaced with
an equivalent resistor such that the battery loading remains
at 10 mA.
HYSTERESIS
When smoke is detected, the resistor/divider network that
sets sensitivity is altered to increase sensitivity. This yields
approximately 100 mV of hysteresis and reduces false
triggering.
Figure 5. Typical Application as Ionization Smoke Detector
TO
OTHER
UNITS
MC145018
1
16
2
3
4
5
6
7
8
15
14
13
12
11
10
9
330
8.2 M
9 V
+
0.1
μ
F
1.5 M
*
0.001
μ
F
220 k
*
0.1
μ
F
1 M
1 M
TEST
*NOTE: Component values may
change depending on type of
piezoelectric horn used.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC14503B | Hex Non-Inverting 3-State Buffer |
| MC14503BCP | Hex Non-Inverting 3-State Buffer |
| MC14503BD | Full Featured -48V Hot Swap Power Manager, Industrial Temp. 14-TSSOP -40 to 85 |
| MC14503BDR2 | Full Featured -48V Hot Swap Power Manager, Industrial Temp. 14-TSSOP -40 to 85 |
| MC14503BF | Full Featured -48V Hot Swap Power Manager, Industrial Temp. 44-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC145018P | 功能描述:IC SMOKE DETECT PHOTOELEC 16-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| MC145026D | 功能描述:鎖相環 - PLL Encoder RoHS:否 制造商:Silicon Labs 類型:PLL Clock Multiplier 電路數量:1 最大輸入頻率:710 MHz 最小輸入頻率:0.002 MHz 輸出頻率范圍:0.002 MHz to 808 MHz 電源電壓-最大:3.63 V 電源電壓-最小:1.71 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:QFN-36 封裝:Tray |
| MC145026DR2 | 功能描述:IC ENCODER 9 LINE SMPLX 16-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:4000 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799 |
| MC145026P | 功能描述:IC ENCODER 9LINE SIMPLEX 16-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:4000 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799 |
| MC145027DW | 功能描述:鎖相環 - PLL Decoder RoHS:否 制造商:Silicon Labs 類型:PLL Clock Multiplier 電路數量:1 最大輸入頻率:710 MHz 最小輸入頻率:0.002 MHz 輸出頻率范圍:0.002 MHz to 808 MHz 電源電壓-最大:3.63 V 電源電壓-最小:1.71 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:QFN-36 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。