- 您現在的位置：買賣IC網 > PDF目錄11207 > MB95F128DPF-GE1 (Fujitsu Semiconductor America Inc)IC MCU FLASH 60K ROM 100QFP PDF資料下載
參數資料
| 型號： | MB95F128DPF-GE1 |
| 廠商： | Fujitsu Semiconductor America Inc |
| 文件頁數： | 8/67頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU FLASH 60K ROM 100QFP |
| 標準包裝： | 1 |
| 系列： | F²MC MB95120 |
| 核心處理器： | F²MC-8FX |
| 芯體尺寸： | 8-位 |
| 速度： | 16MHz |
| 連通性： | I²C，LIN，SIO，UART/USART |
| 外圍設備： | LCD，LVD，POR，PWM，WDT |
| 輸入/輸出數： | 87 |
| 程序存儲器容量： | 60KB（60K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 2K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.8 V ~ 3.3 V |
| 數據轉換器： | A/D 12x8/10b |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 100-QFP |
| 包裝： | 托盤 |
| 產品目錄頁面： | 722 (CN2011-ZH PDF) |
| 其它名稱： | 865-1073 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
MB95120 Series
16
■ HANDLING DEVICES
Preventing Latch-up
Care must be taken to ensure that maximum voltage ratings are not exceeded when they are used.
Latch-up may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-withstand voltage pins or if higher than the rating voltage is applied between VCC
pin and VSS pin.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements.
Also, take care to prevent the analog power supply voltage (AVCC , AVR) and analog input voltage from exceeding
the digital power supply voltage (VCC) when the analog system power supply is turned on or off.
Stable Supply Voltage
Supply voltage should be stabilized.
A sudden change in power-supply voltage may cause a malfunction even within the guaranteed operating range
of the VCC power-supply voltage.
For stabilization, in principle, keep the variation in VCC ripple (p-p value) in a commercial frequency range
(50/60 Hz) not to exceed 10
% of the standard VCC value and suppress the voltage variation so that the transient
variation rate does not exceed 0.1 V/ms during a momentary change such as when the power supply is switched.
Precautions for Use of External Clock
Even when an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from sub clock mode or stop mode.
■ PIN CONNECTION
Treatment of Unused Pin
Leaving unused input pins unconnected can cause abnormal operation or latch-up, leaving to permanent
damage.
Unused input pins should always be pulled up or down through resistance of at least 2 k
. Any unused input/
output pins may be set to output mode and left open, or set to input mode and treated the same as unused input
pins. If there is unused output pin, make it open.
Treatment of Power Supply Pins on A/D Converter
Connect to be AVCC
= VCC and AVSS = AVR = VSS even if the A/D converter is not in use.
Noise riding on the AVCC pin may cause accuracy degradation. So, connect approx. 0.1
F ceramic capacitor
as a bypass capacitor between AVCC and AVSS pins in the vicinity of this device.
Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS near
this device.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B2X-IX-F3 | CONVERTER MOD DC/DC 5.2V 75W |
| ATSAM3U2CA-AU | IC MCU 32BIT 128KB FLASH 100LQFP |
| VI-B2X-IX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
| AT91SAM7S128C-AU-999 | IC MCU ARM7 128KB FLASH 64LQFP |
| VI-B2X-IX-F1 | CONVERTER MOD DC/DC 5.2V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB95F128DPMC | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95F128DPMC-GE1 | 功能描述:IC MCU FLASH 60K ROM 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:F²MC MB95120 產品培訓模塊:The Ultra-Low Power MSP430 MSP430 Overview MSP430 Design Tools MSP430 Peripherals MSP430x2xx/4xx and Wireless Overview Portable Medical Solutions with MSP430 MSP430 for Utility Metering Solutions MSP430: How to JTAG MSP430, How To Use the Clock System Grace Software Graphical User Interface MCU Overview Driver Library MSP430Ware Overview 標準包裝:1 系列:MSP430x4xx 核心處理器:RISC 芯體尺寸:16-位 速度:8MHz 連通性:SPI，UART/USART 外圍設備:欠壓檢測/復位，LCD，POR，PWM，WDT 輸入/輸出數:48 程序存儲器容量:32KB（32K x 8 + 256B） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:100-LQFP 包裝:Digi-Reel® 其它名稱:296-26232-6 |
| MB95F128E | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95F128EPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95F128EPMC | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。