- 您現在的位置：買賣IC網 > PDF目錄1947 > MB91F478PMC1-GE1 (Fujitsu Semiconductor America Inc)IC MCU 384KB FLASH 144LFQFP PDF資料下載
參數資料
| 型號： | MB91F478PMC1-GE1 |
| 廠商： | Fujitsu Semiconductor America Inc |
| 文件頁數： | 18/94頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 384KB FLASH 144LFQFP |
| 標準包裝： | 1 |
| 系列： | FR MB91470 |
| 核心處理器： | FR60 RISC |
| 芯體尺寸： | 32-位 |
| 速度： | 80MHz |
| 連通性： | EBI/EMI，I²C，F(xiàn)IFO，SIO |
| 外圍設備： | DMA，PWM，WDT |
| 輸入/輸出數： | 113 |
| 程序存儲器容量： | 384KB（384K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 24K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4 V ~ 5.5 V |
| 數據轉換器： | A/D 12x8/10b，4x12b |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 144-LQFP |
| 包裝： | 托盤 |
| 其它名稱： | 865-1094 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
MB91470/480 Series
25
■ HANDLING DEVICES
Preventing latch-up
Latch-up phenomenon may occur with CMOS IC, when a voltage higher than VCC or lower than VSS is applied
to either the input or output terminals, or when a voltage is applied between VCC pin and VSS pin that exceeds the
rated voltage. When latch-up occurs, a significant power-supply current surge results, which may damage some
elements due to the excess heat, so great care must be taken to ensure that the maximum rating is never
exceeded during use.
Treatment of unused input pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by, for example, using a
pull-up or pull-down resistor.
Power pins
In products with multiple VCC and VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to the same potential power
supply and a ground line externally to lower the electro-magnetic emission level, to prevent abnormal operation
of strobe signals caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic capacitor of approximately 0.1
F as a bypass capacitor between VCC
and VSS near this device.
Crystal oscillator circuit
Noise near the X0 and X1 pins may cause the device to malfunction. Design the printed circuit board so that X0,
X1, the crystal oscillator (or ceramic oscillator), and the bypass capacitor to ground are located as close to the
device as possible.
It is strongly recommended to design the PC board artwork with the X0 and X1pins surrounded by ground plane
because stable operation can be expected with such a layout. Please ask the crystal maker to evaluate the
oscillational characteristics of the crystal and this device.
About mode pins (MD0 to MD2)
These pins should be connected directly to VCC pin or VSS pin.
Design the printed circuit board such that the pull-up/down resistance stays low, as well as the distance between
the mode pins and power supply or GND pins is as short as possible and the connection impedance is low,
when the pins are pulled-up/down such as for switching the pin level and rewriting the Flash memory data. It is
because of preventing the device erroneously switching to test mode due to noise.
Operation at start-up
Be sure to execute setting initialized reset (INIT) with INITX pin immediately after start-up.
Immediately after that, also, hold the "L"-level input to the INITX pin for the stabilization wait time required for the
oscillator circuit to take the oscillation stabilization wait time for the oscillator circuit and the stabilization wait
time for the regulator (For INIT via the INITX pin, the oscillation stabilization wait time setting is initialized to the
minimum value).
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F662PMC-GE1 | IC MCU 512KB FLASH FR80 120-LQFP |
| MB95F108AJWPMC-GE1 | IC MCU 60K FLASH 64-LQFP |
| MB95F118JWPMC-GE1 | IC MCU 60K FLASH 2KB RAM 52LQFP |
| MB95F128DPMC-GE1 | IC MCU FLASH 60K ROM 100LQFP |
| MB95F128JBPF-GE1 | IC MCU 60KB FLASH 100QFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F479 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontrollers |
| MB91F479BGL-GE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontrollers |
| MB91F479PM1RGE1 | 制造商:FUJITSU 功能描述:Pb Free |
| MB91F479PM1R-GE1 | 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 32BIT FR 512K FLASH 144QFP |
| MB91F479PMC1-GE1 | 功能描述:IC MCU 512KB FLASH 144-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:FR MB91470 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發布緊急采購，3分鐘左右您將得到回復。