參數資料
型號： MB91F469GAPB-GS
元件分類： 微控制器/微處理器
英文描述： 32-BIT, FLASH, 88 MHz, RISC MICROCONTROLLER, PBGA320
封裝： 27 X 27 MM, 2.46 MM HEIGHT, 1.27 MM PITCH, PLASTIC, BGA-320
文件頁數： 86/159頁
文件大?。?/td> 4658K
代理商： MB91F469GAPB-GS
MB91460G Series
32
6.
Mode pins (MD_x)
These pins should be connected directly to the power supply or ground pins. To prevent the device from entering
test mode accidentally due to noise, minimize the lengths of the patterns between each mode pin and power
supply pin or ground pin on the printed circuit board as possible and connect them with low impedance.
7.
Notes on operating in PLL clock mode
If the oscillator is disconnected or the clock input stops when the PLL clock is selected, the microcontroller may
continue to operate at the free-running frequency of the self-oscillating circuit of the PLL. However, this self-
running operation cannot be guaranteed.
8.
Pull-up control
The AC standard is not guaranteed in case a pull-up resistor is connected to the pin serving as an external bus pin.
9.
Notes on PS register
As the PS register is processed in advance by some instructions, when the debugger is being used, the exception
handling may result in execution breaking in an interrupt handling routine or the displayed values of the ags in
the PS register being updated.
As the microcontroller is designed to carry out reprocessing correctly upon returning from such an EIT event,
the operation before and after the EIT always proceeds according to specication.
1) The following behavior may occur if any of the following occurs in the instruction immediately after a DIV0U/
DIV0S instruction:
(a) a user interrupt or NMI is accepted; (b) single-step execution is performed; or (c) execution breaks due
to a data event or from the emulator menu.
-D0 and D1 ags are updated in advance.
-An EIT handling routine (user interrupt/NMI or emulator) is executed.
-Upon returning from the EIT, the DIV0U/DIV0S instruction is executed and the D0 and D1 ags are updated
to the same values as those in 1).
2) The following behavior occurs when an ORCCR, STILM, MOV Ri or PS instruction is executed to enable a
user interrupt or NMI source while that interrupt is in the active state.
-The PS register is updated in advance.
-An EIT handling routine (user interrupt/NMI or emulator) is executed.
- Upon returning from the EIT, the above instructions are executed and the PS register is updated to the
same value as in 1).
PRELIMINARY
相關PDF資料
PDF描述
MB91F469QAPB-GSE1 RISC MICROCONTROLLER, PBGA320
MB91F469TAPMC-GSE2 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144
MB91F467TAPMC-GSE2 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144
MB91F475PMC1-GE1 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144
MB91482PMC-GE1 32-BIT, MROM, 80 MHz, RISC MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
MB91F469GBPB-ESE1 制造商:FUJITSU 功能描述:
MB91F469GBPB-GSE1 制造商:FUJITSU 功能描述:
MB91F475 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontrollers
MB91F475BGL-GE1 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontrollers
MB91F475PMC1-GE1 功能描述:IC MCU 256KB FLASH 144-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:FR MB91470 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*