- 您現在的位置：買賣IC網 > PDF目錄45193 > MB91F365GB 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB91F365GB |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封裝： | PLASTIC, QFP-120 |
| 文件頁數： | 25/64頁 |
| 文件大?。?/td> | 800K |
| 代理商： | MB91F365GB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
FME / EMDC / Br - mb91f365g_f366g_ds.fm
31
9-Jan-02
CHAPTER 3
IO-Map
see appendix A.
The addresses shown in this table for CAN registers are based on the settings for CS7 done in the Boot ROM
CHAPTER 4
Interrupt Vector Table
see appendix B
CHAPTER 5
Power-on-sequence
All VDD pins should be connected to the same potential. The analogue supply voltage (AVCC) must not be turned
on before the digital supply voltage.
Immediately after power on always execute INIT at the INITX pin (input a low level to the INITX pin). Hold this low
level at the INITX pin long enough so that after release of the low level at INITX and the passing of the built in
waiting time stable oscillation of the oscillation circuit is achieved. INITX must be pulled low for at least 8 cycles of
the 4 MHz oscillation clock.
CHAPTER 6
Handling of Unused Input Pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the de-
vice. Therefore they must be tied to VDD or VSS through resistors. In this case those resistors should be more
than 2 KOhm.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
The resistor of more than 2 KOhm is used to limit currents through the protection diodes. In case of voltages at the
unused pin of 0.3 V or more below VSS or 0.3 V or more above VDD currents which could cause latch-up will flow
through those diodes. It is possible to use one resistor to connect several pins to VDD or VSS. Care should be
taken not to connect pins from different supply voltage domains to one resistor.
CHAPTER 7
Emulation Device
MB91FV360GA can be used as an emulation device for MB91F365GB/F366GB/366GA. MB91F365GB/F366GB/
366GA use the following resources of MB91FV360G (see MB91FV360GA IO-Map):
Reload Timer 0 - Reload Timer 5
UART 0 / U-Timer 0 - UART 1 / U-Timer 1
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F366GB | 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F368GBPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F366GBPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F364GPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F365GBPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F365GBPMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB91F365GBPMCR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB91F365GBPMT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
| MB91F366GB | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
| MB91F366GBPMC3-G | 功能描述:MCU 32-BIT FR50 RISC 512KB FLASH RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:FR MB91360G 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發布緊急采購，3分鐘左右您將得到回復。