參數資料
型號: MB90803PF-G
廠商: FUJITSU LTD
元件分類: 微控制器/微處理器
英文描述: 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP100
封裝: 20 X 14 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100
文件頁數: 7/92頁
文件大小: 2178K
代理商: MB90803PF-G
MB90800 Series
DS07-13733-6E
15
5.
Treatment of power supply pins (VCC/VSS)
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect all power supply pins to external
power supply and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of
strobe signals caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic capacitor of approximately 0.1
μF as a bypass capacitor between VCC
and VSS near this device.
6.
About Crystal oscillators circuit
Noise near the X0/X1 pins and X0A/X1A pins may cause the device to malfunction. Design the printed circuit
board so that X0/X1 pins and X0A/X1A pins, the crystal oscillator (or the ceramic oscillator) and the bypass
capacitor to ground are located as close to the device as possible.
It is strongly recommended to design the PC board artwork with the X0/X1 pins and X0A/X1A pins surrounded
by ground plane because stable operation can be expected with such a layout.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
7.
Caution on Operations during PLL Clock Mode
On this microcontroller, if in case the crystal oscillator breaks off or an external reference clock input stops while
the PLL clock mode is selected, a self-oscillator circuit contained in the PLL may continue its operation at its
self-running frequency. However, Fujitsu will not guarantee results of operations if such failure occurs.
8.
Stabilization of Supply Power Supply
A sudden change in the supply voltage may cause the device to malfunction even within the VCC supply voltage
operating range.Therefore, the VCC supply voltage should be stabilized. For reference, the supply voltage should
be controlled so that VCC ripple variations (peak- to-peak values) at commercial frequencies (50 Hz/60 Hz) fall
below 10
% of the standard VCC supply voltage and the coefficient of fluctuation does not exceed 0.1 V/ms at
instantaneous power switching.
9.
Note on Using the two-subsystem product as one-subsystem product
If you are using only one subsystem of the MB90800 series that come in one two-subsystem product, use it with
X0A
= VSS and X1A = OPEN.
10. Write to FLASH
Ensure that you must write to FLASH at the operating voltage VCC
= 3.0 V to 3.6 V.
相關PDF資料
PDF描述
MPC8255CZUHFBXXX 32-BIT, 166 MHz, RISC PROCESSOR, PBGA480
MPC8347VRALF 32-BIT, 667 MHz, RISC PROCESSOR, PBGA620
MC9S12XEP100F1CAL 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP112
MC9S12XEP100F1VAGR 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP144
MB90341EPF 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
MB90803S 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Microcontroller
MB90803SPF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller CMOS
MB90803SPF-G 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Microcontroller
MB90820 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB90820B 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Microcontroller