參數資料
型號： MB89485LPMC
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PQFP64
封裝： 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-64
文件頁數： 7/56頁
文件大?。?/td> 1476K
代理商： MB89485LPMC
MB89480 Series
DS07-12559-2E
15
■ HANDLING DEVICES
1.
Preventing Latch-up
Latch-up may occur on CMOS IC if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- to high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in
■ ELECTRICAL CHARACTERISTICS is applied between VCC and VSS.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AVCC) and analog input from exceeding the digital power
supply (VCC) when the analog system power supply is turned on and off.
2.
Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistor.
3.
Treatment of Power Supply Pins on Microcontrollers with A/DConverter
Connect to be AVCC = VCC and AVSS = VSS even if the A/D converter is not in use.
4.
Treatment of N.C. Pins
Be sure to leave (internally connected) N.C. pins open.
5.
Power Supply Voltage Fluctuations
Although VCC power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P
value) will be less than 10% of the standard VCC value at the commercial frequency (50 to 60 Hz) and the transient
fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched.
6.
Precautions when Using an External Clock
Even when an external clock is used, oscillation stabilization time is required for power-on reset and wake-up
from stop mode.
7.
Notes on noise in the External Reset Pin (RST)
If the reset pulse applied to the external reset pin (RST) does not meet the specifications, it may cause malfunc-
tions. Use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (RST).
相關PDF資料
PDF描述
MB89P485-101PMC MICROCONTROLLER, PQFP64
MB89P538PF-101 8-BIT, OTPROM, 12.5 MHz, MICROCONTROLLER, PQFP64
MB89535APFV 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PQFP64
MB89535AP 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PDIP64
MB89P538-101PV 8-BIT, OTPROM, 12.5 MHz, MICROCONTROLLER, PBCC64
相關代理商/技術參數
參數描述
MB89485LP-SH 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
MB89485PFM 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
MB89485P-SH 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
MB89490 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
MB89490_03 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller CMOS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*