- 您現在的位置：買賣IC網 > PDF目錄383545 > MAX997 (Maxim Integrated Products, Inc.) Hex 2-Input NAND Drivers 20-CFP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX997 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Hex 2-Input NAND Drivers 20-CFP -55 to 125 |
| 中文描述： | 單/雙/四路、超高速、+3V/+5V、超擺幅比較器 |
| 文件頁數： | 9/12頁 |
| 文件大小： | 371K |
| 代理商： | MAX997 |
M
Single/Dual/Quad, Ultra-High-Speed, +3V/+5V,
Beyond-the-Rails Comparators
_______________________________________________________________________________________
9
Output Stage Circuitry
The MAX961–MAX964/MAX997/MAX999 contain a cur-
rent-driven output stage, as shown in Figure 4. During an
output transition, I
SOURCE
or I
SINK
is pushed or pulled to
the output pin. The output source or sink current is high
during the transition, creating a rapid slew rate. Once the
output voltage reaches V
OH
or V
OL
, the source or sink
current decreases to a small value, capable of maintain-
ing the V
OH
or V
OL
in static condition. This decrease in
current conserves power after an output transition has
occurred.
One consequence of a current-driven output stage is a
linear dependence between the slew rate and the load
capacitance. A heavy capacitive load slows down the
voltage output transition.
Shutdown Mode
When SHDN is high, the MAX961/MAX963/MAX964/
MAX997 shut down. When shut down, the supply cur-
rent drops to 270μA per comparator, and the outputs
become high impedance. SHDN has a high input
impedance. Connect SHDN to GND for normal opera-
tion. Exit shutdown with LE low; otherwise, the output is
indeterminate.
__________Applications Information
Circuit Layout and Bypassing
The MAX961–MAX964/MAX997/MAX999’s high band-
width requires a high-speed layout. Follow these layout
guidelines:
1) Use a printed circuit board with a good, unbroken,
low-inductance ground plane.
2) Place a decoupling capacitor (a 0.1μF ceramic sur-
face-mount capacitor is a good choice) as close to
V
CC
as possible.
3) On the inputs and outputs, keep lead lengths short
to avoid unwanted parasitic feedback around the
comparators. Keep inputs away from outputs. Keep
impedance between the inputs low.
4) Solder the device directly to the printed circuit board
rather than using a socket.
5) Refer to Figure 5 for a recommended circuit layout.
6) For slow-moving input signals, take care to prevent
parasitic feedback. A small capacitor (1000pF or
less) placed between the inputs can help eliminate
oscillations in the transition region. This capacitor
causes negligible degradation to t
PD
when the
source impedance is low.
Figure 4. Output Stage Circuitry
MAX961-MAX964
MAX997
MAX999
I
SOURCE
Q, Q
V
CC
GND
I
SINK
Figure 5. MAX961 PC Board Layout
相關PDF資料 |
PDF描述 |
|---|---|
| MAX997ESA | Hex 2-Input NAND Drivers 20-CDIP -55 to 125 |
| MAX961 | Octal Buffers/Drivers With 3-State Outputs 20-LCCC -55 to 125 |
| MAX961ESA | Octal Buffers/Drivers With 3-State Outputs 20-CDIP -55 to 125 |
| MAX962 | Octal Buffers/Drivers With 3-State Outputs 20-CFP -55 to 125 |
| MAX962ESA | Octal Registered Transceivers With 3-State Outputs 28-LCCC -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9972ACCS+D | 制造商:Maxim Integrated Products 功能描述:QUAD ULTRA-LOW-POWER 300MBPS ATE - Rail/Tube |
| MAX9972ACCS+DW | 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MAX9972ACCS+DW-T | 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MAX9972ACCS+TD | 制造商:Maxim Integrated Products 功能描述:QUAD, ULTRA-LOW-POWER, 300MBPS ATE DRIVERS/COMPARATORS 80TQF - Tape and Reel |
| MAX9972ACCS-DW | 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。