- 您現在的位置：買賣IC網 > PDF目錄296470 > MAX9966BGCCQ+D (MAXIM INTEGRATED PRODUCTS INC) Quad, Low-Power, 500Mbps ATE Driver/Comparator PDF資料下載
參數資料
| 型號： | MAX9966BGCCQ+D |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 比較器 |
| 英文描述： | Quad, Low-Power, 500Mbps ATE Driver/Comparator |
| 中文描述： | QUAD COMPARATOR, 100000 uV OFFSET-MAX, 1.2 ns RESPONSE TIME, PQFP100 |
| 封裝： | 14 X 14 MM, 0.50 MM PITCH, 1 MM HEIGHT, ROHS COMPLIANT, TQFP-100 |
| 文件頁數： | 10/28頁 |
| 文件大?。?/td> | 809K |
| 代理商： | MAX9966BGCCQ+D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
MAX9965/MAX9966
Quad Low-Power, 500Mbps
ATE Driver/Comparator
18
______________________________________________________________________________________
Detailed Description
The MAX9965/MAX9966 four-channel, high-speed pin
electronics driver and comparator ICs for automatic test
equipment include, for each channel, a three-level pin
driver, a dual comparator, and variable clamps (Figure
1). The driver features a -1.5V to +6.5V operating range
and high-speed operation, including high-Z and active
termination (3rd-level drive) modes, which is highly lin-
ear even at low-voltage swings. The devices are similar
to the MAX9963/MAX9964 but with a comparator that
provides even lower timing dispersion, due to changes
in input slew rate and pulse width. The clamps provide
damping of high-speed DUT_ waveforms when the
device is configured as a high-impedance receiver.
Each of the four channels has high-speed, differential
inputs compatible with ECL, LVPECL, LVDS, and GTL
signal levels, with optional 100
Ω differential input termi-
nations. Optional internal resistors at DATA_ and RCV_
provide differential termination of LVDS inputs. Optional
internal resistors at CH_ and CL_ provide the pullup
voltage and source termination for open-collector com-
parator outputs. These options significantly reduce the
discrete component count on the circuit board.
The MAX9965/MAX9966 are available in two grade
options. An A-grade version provides tighter matching of
gain and offset of the drivers, and tighter offset matching
of the comparators. This allows reference levels to be
shared across multiple channels in cost-sensitive sys-
tems. A B-grade version provides lower cost for system
designs that incorporate independent reference levels for
each channel.
The MAX9965/MAX9966 modal operation is pro-
grammed through a 3-wire, low-voltage, CMOS-com-
patible serial interface.
Output Driver
The driver input is a high-speed multiplexer that selects
one of three voltage inputs: DHV_, DLV_, or DTV_. This
switching is controlled by high-speed inputs DATA_
and RCV_, and mode control bit TMSEL. A slew-rate
circuit controls the slew rate of the buffer input. One of
four possible slew rates can be selected (Table 1); the
speed of the internal multiplexer sets the 100% driver
slew rate (see the Driver Large-Signal Response in the
Typical Operating Characteristics).
DUT_ can be toggled at high speed between the buffer
output and high-impedance mode, or it can be placed
in low-leakage mode (Figure 2, Table 2). In high-imped-
ance mode, the clamps are connected. This switching
is controlled by the high-speed input RCV_ and the
mode control bits TMSEL and LLEAK. In high-imped-
ance mode, the bias current at DUT_ is less than 2A
over the 0 to 3V range, while the node maintains its
ability to track high-speed signals. In low-leakage
mode, the bias current at DUT_ is further reduced to
less than 15nA. See the Low-Leakage Mode section for
more detailed information.
The nominal driver output resistance is 50
Ω. Contact the
factory for different values within the 40
Ω to 50Ω range.
SLEW RATE
DLV_
DHV_
DTV_
DATA_
RCV_
MODE
BUFFER
50
Ω
DUT_
4
CPHV_
CPLV_
HIGH-Z
0
1
HIGH-
SPEED
INPUTS
REFERENCE
INPUTS
COMPARATORS
CLAMPS
TMSEL
SC0
SC1
LLEAK
Figure 2. Simplified Driver Channel
相關PDF資料 |
PDF描述 |
|---|---|
| MAXQ2000-QBX | Low-Power LCD Microcontroller |
| MAYK062DG | 6.2 V, 0.2 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| MAYS0750Y | 0.15 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| MAZ102F02C02B01A | SNAP ACTING/LIMIT SWITCH, CHANGE-OVER, MOMENTARY, 2.9mm, PANEL MOUNT |
| MAZ104A02C02B01A | SNAP ACTING/LIMIT SWITCH, CHANGE-OVER, MOMENTARY, 2.9mm, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9966BGCCQ-TD | 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MAX9967ADCCQ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX9967ADCCQ+B5A | 功能描述:緩沖器和線路驅動器 Dual Low-Pwr 500Mbps ATE Drvr/Comparator RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MAX9967ADCCQ+D | 功能描述:緩沖器和線路驅動器 Dual 500Mbps ATE Driver/Comparator RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MAX9967ADCCQ+TD | 功能描述:緩沖器和線路驅動器 Dual 500Mbps ATE Driver/Comparator RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。