- 您現在的位置：買賣IC網 > PDF目錄4568 > MAX9951DCCB+D (Maxim Integrated Products)IC PPMU DUAL SPI 64TQFP PDF資料下載
參數資料
| 型號： | MAX9951DCCB+D |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 22/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PPMU DUAL SPI 64TQFP |
| 標準包裝： | 160 |
| 系列： | * |
MAX9951/MAX9952
Dual Per-Pin Parametric
Measurement Units
7
Maxim Integrated
Note 2:
The device operates properly with different supply voltages with equally different voltage swings.
Note 3:
Interpret errors expressed in terms of %FSR (percent of full-scale range) as a percentage of the end-point-to-end-point
range, i.e., for the ±64mA range, the full-scale range = 128mA, and a 1% error = 1.28mA.
Note 4:
Case must be maintained ±5°C for linearity specifications.
Note 5:
Tested in range C.
Note 6:
Current linearity specifications are maintained to within 700mV of the clamp voltages when the clamps are enabled.
Note 7:
Specified as the percent of full-scale range change at the output per volt change in the DUT voltage.
Note 8:
VCLLO_ and VCLHI_ should differ by at least 700mV.
Note 9:
The digital interface accepts +5V, +3.3V, and +2.5V CMOS logic levels. The voltage at VL adjusts the threshold.
Note 10: Guaranteed by design.
Note 11: Settling times are to 0.1% of FSR. CX_ = 60pF.
Note 12: All settling times are specified using a single compensation capacitor (CX_) across all current-sense resistors. Use an indi-
vidual capacitor across each sense resistor for better performance across all current ranges, particularly the lower ranges.
Note 13: The propagation delay time is only guaranteed over the force-voltage output range. Propagation delay is measured by
holding VSENSE_ steady and transitioning THMAX_ or THMIN_.
Note 14: Maximum serial clock frequency may diminish at VL < +3.3V.
AC ELECTRICAL CHARACTERISTICS (continued)
(VCC = +12V, VEE = -7V, VL = +3.3V, CCM_ = 120pF, CL = 100pF, TA = +25°C, unless otherwise noted. Specifications at TA = TMIN
and TA = TMAX are guaranteed by design and characterization. Typical values are at TA = +25°C, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SCLK Fall to DOUT Valid
tDO
22
ns
CS Low to SCLK High
Setup
tCSS0
10
ns
SCLK High to
CS High
Hold
tCSH1
22
ns
SCLK High to
CS Low
Hold
tCSH0
0ns
CS High to SCLK High
Setup
tCSS1
5ns
DIN to SCLK High Setup
tDS
10
ns
DIN to SCLK High Hold
tDH
(Note 13)
0
ns
CS Pulse-Width High
tCSWH
10
ns
CS Pulse-Width Low
tCSWL
10
ns
LOAD Pulse-Width Low
tLDW
20
ns
VDD High to CS Low
(Power-Up)
(Note 13)
500
ns
相關PDF資料 |
PDF描述 |
|---|---|
| LFX125EB-05F256C | IC FPGA 139K GATES 256-BGA |
| LFX125EB-05FN256C | IC FPGA 139K GATES 256-BGA |
| MAX9950DCCB+D | IC PPMU DUAL SPI 64TQFP |
| LFX125EB-04FN256I | IC FPGA 139K GATES 256-BGA |
| MAX9949DCCB+D | IC PPMU DUAL SPI 64TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9951DCCB-TD | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX9951FCCB | 功能描述:數據轉換 IC - 多種 RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
| MAX9951FCCB+ | 功能描述:接口 - 專用 Dual Per-Pin PMU RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX9951FCCB+T | 功能描述:接口 - 專用 Dual Per-Pin PMU RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX9951FCCB-D | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。