- 您現在的位置：買賣IC網 > PDF目錄2012 > MAX9851ETM+T (Maxim Integrated Products)IC CODEC AUDIO STEREO 48TQFN PDF資料下載
參數資料
| 型號： | MAX9851ETM+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 58/71頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CODEC AUDIO STEREO 48TQFN |
| 標準包裝： | 2,500 |
| 類型： | 立體聲音頻 |
| 數據接口： | 串行 |
| 分辨率（位）： | 18 b |
| ADC / DAC 數量： | 2 / 2 |
| 三角積分調變： | 是 |
| S/N 比，標準 ADC / DAC (db)： | 81.5 / 88 |
| 動態范圍，標準 ADC / DAC (db)： | 82 / 87.5 |
| 電壓 - 電源，模擬： | 2.6 V ~ 3.3 V |
| 電壓 - 電源，數字： | 1.7 V ~ 3.3 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-TQFN-EP（7x7） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
MAX9851/MAX9853
Stereo Audio CODECs with Microphone, DirectDrive
Headphones, Speaker Amplifiers, or Line Outputs
______________________________________________________________________________________
61
SCL
SDA
SSr
P
Figure 11. START, STOP, and REPEATED START Conditions
1
SCL
START
CONDITION
SDA
28
9
CLOCK PULSE FOR
ACKNOWLEDGMENT
ACKNOWLEDGE
NOT ACKNOWLEDGE
Figure 12. Acknowledge
Bit Transfer
One data bit is transferred during each SCL cycle. The
data on SDA must remain stable during the high period
of the SCL pulse. Changes in SDA while SCL is high
are control signals (see the START and STOP
Conditions section). SDA and SCL idle high when the
I2C bus is not busy.
START and STOP Conditions
SDA and SCL idle high when the bus is not in use. A
master initiates communication by issuing a START
condition. A START condition is a high-to-low transition
on SDA with SCL high. A STOP condition is a low-to-
high transition on SDA while SCL is high (Figure 11). A
START condition from the master signals the beginning
of a transmission to the MAX9851/MAX9853. The mas-
ter terminates transmission, and frees the bus, by issu-
ing a STOP condition. The bus remains active if a
REPEATED START condition is generated instead of a
STOP condition.
Early STOP Conditions
The MAX9851/MAX9853 recognize a STOP condition at
any point during data transmission except if the STOP
condition occurs in the same high pulse as a START
condition. For proper operation, do not send a STOP
condition during the same SCL high pulse as the
START condition.
Slave Address
The MAX9851/MAX9853 are preprogrammed with a
slave address of 0x20 or 0010000. The address is
defined as the 7 most significant bits (MSBs) followed by
the read/write bit. Set the read/write bit to 1 to configure
the MAX9851/MAX9853 to read mode. Set the read/write
bit to 0 to configure the MAX9851/MAX9853 to write
mode. The address is the first byte of information sent to
the MAX9851/MAX9853 after the START condition.
Acknowledge
The acknowledge bit (ACK) is a clocked 9th bit that the
MAX9851/MAX9853 use to handshake receipt each byte
of data when in write mode (see Figure 12). The
MAX9851/MAX9853 pull down SDA during the entire
master-generated ninth clock pulse if the previous byte is
successfully received. Monitoring ACK allows for detec-
tion of unsuccessful data transfers. An unsuccessful data
transfer occurs if a receiving device is busy or if a system
fault has occurred. In the event of an unsuccessful data
transfer, the bus master may retry communication.
The master pulls down SDA during the ninth clock cycle
to acknowledge receipt of data when the MAX9851/
MAX9853 are in read mode. An acknowledge is sent by
the master after each read byte to allow data transfer to
continue. A not acknowledge is sent when the master
reads the final byte of data from the MAX9851/
MAX9853, followed by a STOP condition.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9856ETL+T | IC AUDIO CODEC 40TQFN-EP |
| MAX9860ETG+T | IC CODEC MONO AUD 16BIT 24TQFN |
| MAX9867ETJ+T | IC STEREO AUD CODEC LP 32TQFN-EP |
| MAX9880AETM+ | IC CODEC AUDIO STEREO 48TQFN |
| MB86064PB-GE1 | DAC 14BIT 1GSA/S DUAL 12-EFBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9851EVCMODU | 功能描述:音頻 IC 開發工具 Evaluation Kit/Evaluation System for the MAX9851 RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX9851EVKIT | 功能描述:音頻 IC 開發工具 Evaluation Kit/Evaluation System for the MAX9851 RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX9853ETM+ | 功能描述:接口—CODEC Stereo Audio CODEC w/DirectDrive Amp RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| MAX9853ETM+T | 功能描述:接口—CODEC Stereo Audio CODEC w/DirectDrive Amp RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| MAX9853EVCMODU | 功能描述:音頻 IC 開發工具 Evaluation Kit/Evaluation System for the MAX9853 RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。