- 您現在的位置：買賣IC網 > PDF目錄383548 > MAX983EPA (MAXIM INTEGRATED PRODUCTS INC) Ultra-Low-Power, Open-Drain, Single/Dual-Supply Comparators PDF資料下載
參數資料
| 型號： | MAX983EPA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Ultra-Low-Power, Open-Drain, Single/Dual-Supply Comparators |
| 中文描述： | DUAL COMPARATOR, 10000 uV OFFSET-MAX, 300000 ns RESPONSE TIME, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-8 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 109K |
| 代理商： | MAX983EPA |
Low-Voltage Operation: V+ = 1V (MAX9_4 Only)
The guaranteed minimum operating voltage is 2.5V (or
±1.25V). As the total supply voltage falls below 2.5V,
performance degrades and the supply current falls.
The reference will not function below about 2.2V,
although the comparators will continue to operate with a
total supply voltage as low as 1V. While the MAX9_4
has comparators that may be used at supply voltages
below 2V, the MAX9_1/MAX9_2/MAX9_3 may not be
used with supply voltages below 2.5V.
At low supply voltages, the comparators’ output sink
capability is reduced and the propagation delay
increases (see Typical Operating Characteristics). The
useful input voltage range extends from the negative
supply to a little under 1V below the positive supply,
which is slightly closer to the positive rail than when the
device operates from higher supply voltages. Test your
prototype over the full temperature and supply-voltage
range if you anticipate operation below 2.5V.
Comparator Output
With 100mV of overdrive, propagation delay is typically
3μs. The Typical Operating Characteristics show the
propagation delay for various overdrive levels. The
open-drain outputs are intended for wire-ORed and
level-shifting applications. The maximum output
voltage is 11V above V-, and may be applied even
when no supply voltage is present (V+ = V-).
The MAX9_1 and MAX9_4 outputs sink current to GND,
making these devices ideal for bipolar to single-ended
conversion and level-shifting applications.
The negative supply does not affect the output sink
current. The positive supply provides gate drive for the
output N-channel MOSFET and heavily influences the
output current capability, especially at low supply
voltages (see Typical Operating Characteristicssection).
The MAX9_2 and MAX9_3 have no GND pin, and their
outputs sink current to V-.
V oltage Referenc e
The internal bandgap voltage reference has an output
of 1.182V above V-. Note that the REF voltage is
referenced to V-, not to GND. Its accuracy is ±1%
(MAX971/MAX973/MAX974) or ±2% (MAX981–MAX984)
in the 0°C to +70°C range. The REF output is typically
capable of sourcing 25μA and sinking 15μA. Do not
bypass the REF output.
Noise Considerations
Although the comparators have a very high gain, useful
gain is limited by noise. This is shown in the Transfer
Function graph (see Typical Operating Characteristics).
As the input voltage approaches the comparator’s
offset, the output begins to bounce back and forth; this
peaks when V
= V
. (The lowpass filter shown on the
graph averages out the bouncing, making the transfer
function easy to observe.) C onsequently, the
comparator has an effective wideband peak-to-peak
noise of around 300μV. The voltage reference has
peak-to-peak noise approaching 1mV. Thus, when a
comparator is used with the reference, the combined
peak-to-peak noise is about 1mV. This, of course, is
much higher than the RMS noise of the individual
components. Take care in your layout to avoid
capacitive coupling from any output to the reference
pin. Crosstalk can significantly increase the actual
noise of the reference.
M
Ultra-Low-Power, Open-Drain,
S ingle/Dual-S upply Comparators
_______________________________________________________________________________________
9
THRESHOLDS
OUT
IN-
IN+
V
HB
HYSTERESIS
BAND
V
REF
- V
HYST
Figure 2. Threshold Hysteresis Band
7
2
5
6
HYST
REF
V-
V+
R1
R2
MAX9_1
MAX982
MAX9_3
2.5V TO11V
I
REF
Figure 3. Programming the HYST Pin
相關PDF資料 |
PDF描述 |
|---|---|
| MAX983ESA | Ultra-Low-Power, Open-Drain, Single/Dual-Supply Comparators |
| MAX984CPE | Ultra-Low-Power, Open-Drain, Single/Dual-Supply Comparators |
| MAX984CSE | Ultra-Low-Power, Open-Drain, Single/Dual-Supply Comparators |
| MAX984EPE | 10-Bit Bus Interface Flip-Flops With 3-State Outputs 24-CDIP -55 to 125 |
| MAX984ESE | Ultra-Low-Power, Open-Drain, Single/Dual-Supply Comparators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX983EPA+ | 功能描述:校驗器 IC Dual Comparator / Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX983ESA | 功能描述:校驗器 IC Dual Comparator / Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX983ESA+ | 功能描述:校驗器 IC Dual Comparator / Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX983ESA+T | 功能描述:校驗器 IC Dual Comparator / Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX983ESA-T | 功能描述:校驗器 IC Dual Comparator / Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。